Some of us continue to wait for a chassis that's been "on the way" for a while, despite AI releasing new rifles in stead. Throw in the VID and a Mexican Standoff ~ complicates my needs..
-
Having trouble using the site?
Contact support
Some of us continue to wait for a chassis that's been "on the way" for a while, despite AI releasing new rifles in stead. Throw in the VID and a Mexican Standoff ~ complicates my needs..
I got my GTAC kit on the 26th, only took 4 days from the UK to my local USPS hub, took 8 days after to get to me. Alan was great to work with, it was mailed on the 14th before the current UK lockdown. I put in my order in October for the run that just got mailed.
New carbon 308 barrel came in the mail last week. Only took 9 months. At that wait time I should have bought another can.
On a side note. I’ve got the comp trigger in and the safety doesn’t work anymore lol that normal? Used it once before I did the swap and it worked fine, not budging now.
On a side note. I’ve got the comp trigger in and the safety doesn’t work anymore lol that normal? Used it once before I did the swap and it worked fine, not budging now.
Did some shooting today out in the grasslands. Beautiful day, dead calm, not too cold and warmed up nicely. The ZCO has been on and off the gun 3 times, the barrel a few times, and just dialed my dope I had written down and this is the 5 shot group I managed at 400 yds. Cold bore, cold shooter. The water line is flipped 90 degrees. It was horizontal. I’m impressed with this thing!!
6.5CM AI barrel 24”
140gr hybrids and lapua SRP brass.
6.5CM AI barrel 24”
140gr hybrids and lapua SRP brass.
Last edited:
Tried to throw my ZCO on my MC, turns out it’s not gonna fithits the rail
On an axmc?
You
shot a 15lb cat with a 300 wm hahahha
Your gonna need 1.50 “ height rings most likely minimum I do believeTried to throw my ZCO on my MC, turns out it’s not gonna fit
I had bought it for my Impact, so I’m not super worried about it. The Razor on there does just fine.
He was actually 33lbs 4 oz. But yeah, not the ideal varmint gun. Was out hunting deer when this guy popped up in the pasture below me. The bullet, a 208 AMax at 2950fps, didn't exit! Cat was sitting on his ass like a dog, facing me at about 300yds. Bullet entered right in his chest. Thought for sure his whole back would be opened up...
Remove the front rail till you can get higher ringsTried to throw my ZCO on my MC, turns out it’s not gonna fit
Guess I'm a part of team AXMC now.
First round impacts to 1050 today with the 6.5 Creed barrel using factory loaded Berger 140's.
Not my first AI but the Kool-Aid has definitely been drunk.
First round impacts to 1050 today with the 6.5 Creed barrel using factory loaded Berger 140's.
Not my first AI but the Kool-Aid has definitely been drunk.
Not all, but with most peoples eye relief the ocular lens sits around where the hinge sits. Meaning the eye piece is clear of the rail anyway.
Might want to double check your LOP then subsequent eye relief.
Might want to double check your LOP then subsequent eye relief.
Question for anyone and everyone. Have any of you tried to get your AX as light as possible to make it a bearable hunting rifle? I have a 24” 6.5cm barrel and a 18” 308 barrel. Love the length of the 308 barrel but definitely still pretty heavy. Thinking about sending the 6.5 barrel to Chad at LRI for some of his crazy fluting or offing both barrels for a carbon barrel, and dumping the Gen 2 razor for a 3-18 MK5 or something along those lines.
What’s the lightest you’ve guys have gotten an AX down to? Priorities have shifted a bit but selling the AI isn’t really an option and the pocket book isn’t big enough for another nice rifle.
What’s the lightest you’ve guys have gotten an AX down to? Priorities have shifted a bit but selling the AI isn’t really an option and the pocket book isn’t big enough for another nice rifle.
A short 18" carbon barrel weighs like .5lb or less than a steel 18" fyi... Carbon barrels are much lighter than steel barrels when comparing longer tubes. I ran a shorty carbon barrel and I couldn't notice any difference humping it around.
The barrel by far is the single largest contributer to weight so if you can get a lighter contour or some heavy fluting you might notice it carrying it around.
My set up weighs like 10lbs with a zco before screwing on a 6-8lb ish barrel
gen2 scope is amazing but certainly HEAVY so your on the right track with new scope/ barrel setup
@trob_205 Slap a 14.5” light contour barrel with some iron sights, or get a gym membership. Your call
ive got a sendero light 6.5CM AX barrel that’s just under 3lbs. An AX with no barrel/optics weighs 9lbs so those would be 12lbs before optic and bipod. Say atlas/ckye single pull ~1lbs so that’s 13lbs. Then whatever optic you want. I have a 3.5-18mk5 that I think would do really well on a hunting gun. You could feasibly get it under or at 16lbs but I’m not sure much under that.
I’d be game for the short ass barrel! And maybe even this says it finished out at 20” within oz of a 16oz carbon barrel.
Where's the night vision?
Needs more sunshade
I’d call it good
Can I borrow yours? I’m thinking of buying one and want to see which set up to get
Borrow? No... Come try out...absolutly anytime you are in Utah you have a standing invitation
For the ones interested & with a 3D printer; I made a simple bag rider for the AXMC. Nothing fancy and definitely not as sophisticated as others I have seen, but it works for me.
Attached some pictures and the STL file for printing (you need to unzip as I cannot upload and STL file).
No special printing settings needed but print upright as shown on the pictures. The version on the picture is PLA with 20% infill, no support. Seems strong enough but I probably will print one from ABS with 40% infill. Probably will also look better as ABS is less shiny. Screw holes are present.
Attached some pictures and the STL file for printing (you need to unzip as I cannot upload and STL file).
No special printing settings needed but print upright as shown on the pictures. The version on the picture is PLA with 20% infill, no support. Seems strong enough but I probably will print one from ABS with 40% infill. Probably will also look better as ABS is less shiny. Screw holes are present.
Got out for some barricade training on Sunday. The AX rocks.
The lightest setup (empty) I have been able to achieve on my AXSA is 13lb-9oz:
AXSA, no bipod
Proof 16.5" .308 barrel w/ APA LB brake
NF ATACR 4-16x50
NF A357 mount with RAP
It's ass heavy like this. I use a 20oz suppressor to balance the rifle, and tame the bark.
Similar threads
