-
Having trouble using the site?
Contact support
Correct. 13” forend clears a 16” barrel. The 16” forend clears 18” barrels
Everything looked good, till I saw that butt pad upside down...
Been playing around with it. I dig it upside down prone but any other position I'm thinking it's not my thing
Someone teach this guy how to take a decent photo with decent lighting...jezz had to take 5 motrin after scrolling thru that thing
killing some time so i got a chance to grab two offset pictures for husky with thevictor rail. a couple downsides to the victor co. rail that you dont get with the AI forend. the mlock pic section isnt a 20 MOA cant. i am also limited by the mlock bolt contacting the barrel when it comes to mounting up the tigIR. i may take a grinderto it one day to see ifi can getit to sit any further back. but itonly takes a minute or two to swap the handguardto the original to getthat full top rail if im gonna be exclusively shooting thermal. the downside to the AI rail is the clip ons will sit even higher. i'll get you some pictures with a 5-20 on the AI rail.
the pvs 30 lines up well with a 5-20US. the thermal is farther forward than is ideal, but i can still shoot stuffwith itjust fine - at least its been proven for me out to about 400 yds. other people will know more than me, but if i am gonna run tigger or the 30 at longer distances id probably exclusively run that on the AI continuous rail
the pvs 30 lines up well with a 5-20US. the thermal is farther forward than is ideal, but i can still shoot stuffwith itjust fine - at least its been proven for me out to about 400 yds. other people will know more than me, but if i am gonna run tigger or the 30 at longer distances id probably exclusively run that on the AI continuous rail
Attachments
Look guy .....I have 4 kids and two giant ass huskies.... it was the only spot in my house not currently occupied with dog hair from shed #3 of the summer, Legos, or baby toys aight ...
Just buy the axsr rail.
I wish yous guys would have mentioned it instead of sending me to buy the dumb sawtooth rail or the Victor rail
WTH!
Cuz mlok is gayier than aides.....
Did they finally release axsr rails with keyslot to the peasants?
WGAF?
What all your strapping to your rifle you need little Dicks all over it?
arca on bottom for pods. Top already has a rail. Side gets a sling swivel. And maybe a barricade stop.
Shout out to @Mile High Shooting for having it in stock and shipping quick
I started my stop watch the second this went up LOL @Huskydriver
Cant run my unnecessary thicc boy with Mlok on the AX either...
We see that elite sand around those hills bout one a year these days...
have it on backorder. i have one of the mlocks that mile high had listed, i just havent had time to mess with it. i prefer the 13" rails vs the 16. thinking i may chop it
AT LoveJust got my first:
Awesome shooting gun - I have never had anything like this but I'm glad I went for it.
I need to get some more mags, a bipod (thinking Atlas w/ spigot), and some kind of sling. I'll also get a set of thumbhole stock sides if they become available again.
. My ATLE only makes me want an MC to join the party. Thumbhole for sure 
. AI never should have strayed from the thumbhole design as a current offering.
Getting same result. “Cold bore” shot after replacing barrel is consistently low. May mitigate that first shot if you’re torquing down a little harder utilizing the wrench flats. @Huskydriver you getting that first shot low impact after barrel swap?? Pretty sure you torque yours on, right?
I smack the barrel on by hand with a wrench before I tighten the quickly screw.
Gives me the most consistent results
That plus tighten the screw to 65
Some of the AXs have too much goop/glue around the barrel locking area and it causes issues
Yea agreed I think I torque mine at 60 iirm I just use a witness mark these days
More tripod practice, getting ready for hunting season.
The AXMC is 3 mile capable!
Congrats to Travis on his 3 shot impact at 5280 yards on a 1 moa target! No warm ups or practice shots either. Cold bore shot was .2 mil high and 1.0 mil right. Second round hit at the base of the target. Third was money! Caliber was 33xc, 32" benchmark barrel by Travis at TS Customs (different Travis) shooting a 300gr Berger at 3190. Congratulations again brother on some incredible shooting!
Congrats to Travis on his 3 shot impact at 5280 yards on a 1 moa target! No warm ups or practice shots either. Cold bore shot was .2 mil high and 1.0 mil right. Second round hit at the base of the target. Third was money! Caliber was 33xc, 32" benchmark barrel by Travis at TS Customs (different Travis) shooting a 300gr Berger at 3190. Congratulations again brother on some incredible shooting!
Tangent Theta 5-25 w T3 reticle. He had a 100 mil charlie tarak with a delta tarac on in front of the scope.
Low Vis Gear, and I really dig them. Only ones I could find for the RRS34.
I don't remember using any factory ammo in this 308 barrel. Just handloads, 1/2 to 3/4 minute usually. Nothing worked up for the rifle.
AXMC and Vudoo V22 in a pale brown master race AICS out for a little sun.
@Defender3 what's the barrel length on your vudoo? I just ordered one and looking to do the same chassis or the aics 2.0 thumb hole
His looks like an 18” barrel.
In order (all in a post 14 ax chassis with a 13” forend and vudoos):
18” kukri Proof Carbon Fiber barrel
20” MTU Ace barrel w/ TBAC 22TD in the end
22” MTU Bartlein barrel
@Krob95
@Defender3
thanks for the info and pics!! I'm jonesing for mine, Went with the 16.5" MTU but will be running a suppressor.
@Defender3
thanks for the info and pics!! I'm jonesing for mine, Went with the 16.5" MTU but will be running a suppressor.
Similar threads
