Accessories Bog Deathgrip Tripod Ball Head Kit

[Duggie]

Pm sent
Thank you

 

[Tanner1776]

I would like to purchase the full kit. I tried to send you a message but I am new to this forum and don’t know if I did it right or not.

 

[STI_1911_Guy]

I would like to purchase the full kit. I tried to send you a message but I am new to this forum and don’t know if I did it right or not.

l will send you a PM. Thanks.

 

[Chado1972]

Would there be anyway I can call you I have questions about your mount I would like to order one but I have a couple questions. Thanks

 

[Chado1972]

****UPDATE***

****I have been working on a printed bushing to replace the aluminum one for a few reasons. Main one being availability, I can print these like any of my other items so sourcing is not an issue. I can also pass the cost savings on to you guys and a little more weight reduction. I will be working on a printed adapter plate in the future also. I wanted to make sure the integrity and strength were both still very sound so I adjusted materials and design until I got it right. ***** There will be nothing new to installation, a dab of Loctite is still highly recommended on the ball head bolt. Just snug it up good, no need to over tighten. There are some variances in the BOG castings so you may hear a slight pop as the lip in the bushing pops over the casting but its fine and expected on some as I keep the fit fairly snug on the bushing.

I have also added an eyebolt addition you can use to hang equipment from. When you purchase it just let me know if you want the eye bolt or regular bolt.

For installation of the eyebolt you will install the bushing then slide the eye bolt up through and tighten fully into the ball head until it bottoms out. Then loosen the eye bolt 1 full turn and lock the nut down while holding the eye bolt from turning if necessary.



I have made up a few ball head conversion kits for the Bog Deathgrip Tripod. I tried to keep the price down as low as possible while maintaining good quality equivalent to the Bog Tripod.

- Prices shipped TYD.
- *** Continually making them as requested. I will inform you of any excessive backlog.
- There are 5 options.

The ball head is rated at 33 lbs and has 360 degree rotation (lockable) base in addition to the ball head and the ball head is lockable and adjustable for tension. This will accept arca-swiss style devices including the numerous picatinny to arca and such items on the market.

To install you would have to remove the one bolt holding the deathgrip to the tripod. Once you do this the bearings and bushings (you will not need these any longer) will come out. You will end up with a hollow casting as seen in the images. Once you have this you can insert the aluminum bushing from the bottom, then insert the new bolt through the bushing and install the ball head onto it. I recommend a dab of Loctite on the bolt before installation.

If you want to use the deathgrip that you just removed you need the kit with the adapter plate. This plate with the 4 supplied screws will attach to the deathgrip head and can then be locked into the arca-swiss ball head.

This entire assembly weighs ~15oz, you will be removing ~8oz to install. So in total you will add about 8 oz to your setup, plus any additional items you decide to add.

Bog Deathgrip Tripod Ball head kit and adapter plate (full kit) $110: This will come with the ball head, bushing and 3/8-16 bolt to attach the ball head. In addition this will come with the adapter plate to attach to the deathgrip that can then be placed into the arca-swiss ball head.
Bog Deathgrip Tripod Ball head kit only $95: This will come with the ball head, bushing and 3/8-16 bolt to attach the ball head.
Bog Deathgrip Bushing, Bolt and Adapter Plate Only $55: This will come with the bushing for the tripod, The 3/8-16 bolt for most ballheads and the adapter plate to attach the deathgrip to Arca-Swiss. This is for if you have your own ballhead but want to be able to attach the deathgrip to it if desired.
Bog Deathgrip Adapter Plate and Screws Only $45: This will come with the adapter plate and 4 screws only.
Bog Deathgrip Bushing and Bolt Only $40: This will com with the bushing and bolt only. This option would be great for someone with their own ballhead and no desire to be able to reattach the deathgrip.


I also have small plates with the standard 1/4-20 screw. If you have any accessories that would benefit from a custom printed fixture that would allow you to attach it to an Arca-Swiss plate, which could then be put on a tripod or something else please send me a PM and we can figure something out.


Items other members have requested

Amp Annealer Bushing Die Holder And Organizer Case Length/Headspace Gauge Organizer Hornady Comparator Organizers Bullet Pullers Expanding Mandrel Organizer Trimmer Brass Catchers Giraud Trimmer Organizer Hornady OAL Organizer K&M Neck Turning Organizer Loading Trays Primer Tube Holders Shellholder Racks WFT Holder AR Upper Hanger Bog Deathgrip Tripod Ball head Area 419 Funnel Organizer Henderson Trimmer Organizer

 

[Chado1972]

Would there be anyway I can call you I have questions about your mount I would like to order one but I have a couple questions. Thanks

Can you please pm me I'm new to this site as well I am very Interested. Thanks .
l will send you a PM. Thanks.

 

[STI_1911_Guy]

Would there be anyway I can call you I have questions about your mount I would like to order one but I have a couple questions. Thanks

I will send you a PM with info. Thanks.

 

[IrishTikka243]

Full kit arrived safely to Ireland, big thanks @STI_1911_Guy

I’ve attached a few pics for reference if anybody is thinking about it.
Very noticeable difference in weight compared with the top heavy Bog saddle.

The printed bushing was a perfect fit - nice and snug. Can’t see any downside to using this over the machined aluminium part (it’s not load bearing).

Ball head feels like good quality and very stable when locked up.

 

[Chado1972]

Do you have any of these ready to ship ? I'm taking it this will work on my 2 year old Bogg tripod that only swings left to right and up and down? If this works when can I order one and how quick can I get it ? How much is the entire kit ? Thanks for your time. Can you email me at [email protected]

 

[Pizzablaster]

Received my full kit and love it! Fit and finish is perfect, install was a breeze in 5 minutes or less and overall improves the feel of the Deathgrip significantly. Thanks again!

 

[Scott Anderson]

I would like the full kit, please pm me, I am new to the page. Thanks in advance

 

[Chado1972]

****UPDATE***

****I have been working on a printed bushing to replace the aluminum one for a few reasons. Main one being availability, I can print these like any of my other items so sourcing is not an issue. I can also pass the cost savings on to you guys and a little more weight reduction. I will be working on a printed adapter plate in the future also. I wanted to make sure the integrity and strength were both still very sound so I adjusted materials and design until I got it right. ***** There will be nothing new to installation, a dab of Loctite is still highly recommended on the ball head bolt. Just snug it up good, no need to over tighten. There are some variances in the BOG castings so you may hear a slight pop as the lip in the bushing pops over the casting but its fine and expected on some as I keep the fit fairly snug on the bushing.

I have also added an eyebolt addition you can use to hang equipment from. When you purchase it just let me know if you want the eye bolt or regular bolt.

For installation of the eyebolt you will install the bushing then slide the eye bolt up through and tighten fully into the ball head until it bottoms out. Then loosen the eye bolt 1 full turn and lock the nut down while holding the eye bolt from turning if necessary.



I have made up a few ball head conversion kits for the Bog Deathgrip Tripod. I tried to keep the price down as low as possible while maintaining good quality equivalent to the Bog Tripod.

- Prices shipped TYD.
- *** Continually making them as requested. I will inform you of any excessive backlog.
- There are 5 options.

The ball head is rated at 33 lbs and has 360 degree rotation (lockable) base in addition to the ball head and the ball head is lockable and adjustable for tension. This will accept arca-swiss style devices including the numerous picatinny to arca and such items on the market.

To install you would have to remove the one bolt holding the deathgrip to the tripod. Once you do this the bearings and bushings (you will not need these any longer) will come out. You will end up with a hollow casting as seen in the images. Once you have this you can insert the aluminum bushing from the bottom, then insert the new bolt through the bushing and install the ball head onto it. I recommend a dab of Loctite on the bolt before installation.

If you want to use the deathgrip that you just removed you need the kit with the adapter plate. This plate with the 4 supplied screws will attach to the deathgrip head and can then be locked into the arca-swiss ball head.

This entire assembly weighs ~15oz, you will be removing ~8oz to install. So in total you will add about 8 oz to your setup, plus any additional items you decide to add.

Bog Deathgrip Tripod Ball head kit and adapter plate (full kit) $110: This will come with the ball head, bushing and 3/8-16 bolt to attach the ball head. In addition this will come with the adapter plate to attach to the deathgrip that can then be placed into the arca-swiss ball head.
Bog Deathgrip Tripod Ball head kit only $95: This will come with the ball head, bushing and 3/8-16 bolt to attach the ball head.
Bog Deathgrip Bushing, Bolt and Adapter Plate Only $55: This will come with the bushing for the tripod, The 3/8-16 bolt for most ballheads and the adapter plate to attach the deathgrip to Arca-Swiss. This is for if you have your own ballhead but want to be able to attach the deathgrip to it if desired.
Bog Deathgrip Adapter Plate and Screws Only $45: This will come with the adapter plate and 4 screws only.
Bog Deathgrip Bushing and Bolt Only $40: This will com with the bushing and bolt only. This option would be great for someone with their own ballhead and no desire to be able to reattach the deathgrip.


I also have small plates with the standard 1/4-20 screw. If you have any accessories that would benefit from a custom printed fixture that would allow you to attach it to an Arca-Swiss plate, which could then be put on a tripod or something else please send me a PM and we can figure something out.


Items other members have requested

Amp Annealer Bushing Die Holder And Organizer Case Length/Headspace Gauge Organizer Hornady Comparator Organizers Bullet Pullers Expanding Mandrel Organizer Trimmer Brass Catchers Giraud Trimmer Organizer Hornady OAL Organizer K&M Neck Turning Organizer Loading Trays Primer Tube Holders Shellholder Racks WFT Holder AR Upper Hanger Bog Deathgrip Tripod Ball head Area 419 Funnel Organizer Henderson Trimmer Organizer

How do I get one of these?

 

[STI_1911_Guy]

Do you have any of these ready to ship ? I'm taking it this will work on my 2 year old Bogg tripod that only swings left to right and up and down? If this works when can I order one and how quick can I get it ? How much is the entire kit ? Thanks for your time. Can you email me at [email protected]

I will send you an email.

 

[STI_1911_Guy]

I will be traveling next week so if you message me I may not respond as quick as I normally try to. Thanks.

I will ship out orders upon my return at the end of the week.

 

[dexhwk]

I was wondering if anyone knows if it's possible to mount the deathgrip on the treepod. I'm a c5 quad and mount it to my wheelchair and think it'll be a lot easier then the original. Bog says its not possible but oddly I do not believe them.

 

[STI_1911_Guy]

I was wondering if anyone knows if it's possible to mount the deathgrip on the treepod. I'm a c5 quad and mount it to my wheelchair and think it'll be a lot easier then the original. Bog says its not possible but oddly I do not believe them.

I will find out or come up with something. I will update you when I have something.

 

[Shep Fuller]

Couple new options added!

Bog Deathgrip Adapter Plate and Screws Only $45: This will come with the adapter plate and 4 screws only.
Bog Deathgrip Bushing, Bolt and Adapter Plate Only (for if you have your own ball head) $50: This will come with the aluminum bushing for the tripod, The 3/8-16 bolt for most ballheads and the adapter plate to attach the deathgrip to Arca-Swiss.

Pm sent

 

[dexhwk]

I will find out or come up with something. I will update you when I have something.

Thank you. It almost looks like the 360 or elevation might work

 

[phacious]

Would like a full kit, PM sent.

 

[Laser1]

PM sent

 

[TBR9300]

****UPDATE***

****I have been working on a printed bushing to replace the aluminum one for a few reasons. Main one being availability, I can print these like any of my other items so sourcing is not an issue. I can also pass the cost savings on to you guys and a little more weight reduction. I will be working on a printed adapter plate in the future also. I wanted to make sure the integrity and strength were both still very sound so I adjusted materials and design until I got it right. ***** There will be nothing new to installation, a dab of Loctite is still highly recommended on the ball head bolt. Just snug it up good, no need to over tighten. There are some variances in the BOG castings so you may hear a slight pop as the lip in the bushing pops over the casting but its fine and expected on some as I keep the fit fairly snug on the bushing.

I have also added an eyebolt addition you can use to hang equipment from. When you purchase it just let me know if you want the eye bolt or regular bolt.

For installation of the eyebolt you will install the bushing then slide the eye bolt up through and tighten fully into the ball head until it bottoms out. Then loosen the eye bolt 1 full turn and lock the nut down while holding the eye bolt from turning if necessary.



I have made up a few ball head conversion kits for the Bog Deathgrip Tripod. I tried to keep the price down as low as possible while maintaining good quality equivalent to the Bog Tripod.

- Prices shipped TYD.
- *** Continually making them as requested. I will inform you of any excessive backlog.
- There are 5 options.

The ball head is rated at 33 lbs and has 360 degree rotation (lockable) base in addition to the ball head and the ball head is lockable and adjustable for tension. This will accept arca-swiss style devices including the numerous picatinny to arca and such items on the market.

To install you would have to remove the one bolt holding the deathgrip to the tripod. Once you do this the bearings and bushings (you will not need these any longer) will come out. You will end up with a hollow casting as seen in the images. Once you have this you can insert the aluminum bushing from the bottom, then insert the new bolt through the bushing and install the ball head onto it. I recommend a dab of Loctite on the bolt before installation.

If you want to use the deathgrip that you just removed you need the kit with the adapter plate. This plate with the 4 supplied screws will attach to the deathgrip head and can then be locked into the arca-swiss ball head.

This entire assembly weighs ~15oz, you will be removing ~8oz to install. So in total you will add about 8 oz to your setup, plus any additional items you decide to add.

Bog Deathgrip Tripod Ball head kit and adapter plate (full kit) $110: This will come with the ball head, bushing and 3/8-16 bolt to attach the ball head. In addition this will come with the adapter plate to attach to the deathgrip that can then be placed into the arca-swiss ball head.
Bog Deathgrip Tripod Ball head kit only $95: This will come with the ball head, bushing and 3/8-16 bolt to attach the ball head.
Bog Deathgrip Bushing, Bolt and Adapter Plate Only $55: This will come with the bushing for the tripod, The 3/8-16 bolt for most ballheads and the adapter plate to attach the deathgrip to Arca-Swiss. This is for if you have your own ballhead but want to be able to attach the deathgrip to it if desired.
Bog Deathgrip Adapter Plate and Screws Only $45: This will come with the adapter plate and 4 screws only.
Bog Deathgrip Bushing and Bolt Only $40: This will com with the bushing and bolt only. This option would be great for someone with their own ballhead and no desire to be able to reattach the deathgrip.


I also have small plates with the standard 1/4-20 screw. If you have any accessories that would benefit from a custom printed fixture that would allow you to attach it to an Arca-Swiss plate, which could then be put on a tripod or something else please send me a PM and we can figure something out.


Items other members have requested

Amp Annealer Bushing Die Holder And Organizer Case Length/Headspace Gauge Organizer Hornady Comparator Organizers Bullet Pullers Expanding Mandrel Organizer Trimmer Brass Catchers Giraud Trimmer Organizer Hornady OAL Organizer K&M Neck Turning Organizer Loading Trays Primer Tube Holders Shellholder Racks WFT Holder AR Upper Hanger Bog Deathgrip Tripod Ball head Area 419 Funnel Organizer Henderson Trimmer Organizer

I would like the full kit..
Could you send a pm with payment info?

 

[phacious]

@STI_1911_Guy ships faster than Prime shipping. I'm extremely pleased with this upgrade, its a game changer.

 

[extendoclip]

I’ll take a full kit if you have one available

 

[Cableman72]

I need another full kit

 

[justpassingthru]

I just ordered the tripod and want to get this kit, can I attach a spotter to this with the full kit? Any insight appreciated, thx

 

[STI_1911_Guy]

I just ordered the tripod and want to get this kit, can I attach a spotter to this with the full kit? Any insight appreciated, thx

Sending you a PM.

 

[Fl Panhandler]

Sent you a PM. I already have a ball head. Thanks.

 

[Stra8shooter]

Have no idea how to send a PM but I am interested in the aluminum plug and bolt. I have the ball head.

How do I connect with you to pay and provide my address to ship.

Thank you

James

 

[JestersHK]

Interested in this, but will it fit the BOG Adrenaline tripod? Do you have adapter plates for mounting direct to a quad rail?
Thanks,

 

[STI_1911_Guy]

Interested in this, but will it fit the BOG Adrenaline tripod? Do you have adapter plates for mounting direct to a quad rail?
Thanks,

Hello, no this will not work with the adrenaline tripod.

 

[STI_1911_Guy]

The next batch of orders will be going out this weekend, if you are interested I have some available.

Thanks Everyone!

 

[Fl Panhandler]

My”kit” fit perfectly. It made my tripod much more user friendly & more stable. Highly recommended. Great job STI_1911_Guy.

 

[KunselGuy]

new to site i think i sent you a pm
would like to order

 

[baculum]

I would like to order Bog Deathgrip Bushing, Bolt and Adapter Plate. I'm new to SH so not sure how to proceed.
Thanks!

 

[Jared102000]

I would like to purchase the full kit if and when you have one available.

 

[Kmay87]

I will take a full kit.

 

[243-220 Swift]

I pm you yesterday for a complete kit , I'm new to the forum and not sure you got it .

 

[nmycon]

Couple new options added!

Bog Deathgrip Adapter Plate and Screws Only $45: This will come with the adapter plate and 4 screws only.
Bog Deathgrip Bushing, Bolt and Adapter Plate Only (for if you have your own ball head) $50: This will come with the aluminum bushing for the tripod, The 3/8-16 bolt for most ballheads and the adapter plate to attach the deathgrip to Arca-Swiss.

Hi! Just wondering if these are still available.

I am interested in the kit with the bushing, bolt and adapter plate (would prefer the aluminum bushing if possible).

Thanks!

(Occurred to me I should probably send a PM as well... )

 

[kukai]

PM sent

 

[charthoorn]

Hey I am interested in the Bog Deathgrip Bushing, Bolt and Adapter Plate Only kit. Would you want to send me a PM? Thank you!

 

[Mtnmn53]

I have the Bog Deathgrip tripod.
I’m interested in purchasing the ball adapter kit complete so that I may continue to use the deathgrip clamp. I assume that the complete kit comes with the adapter plate for the original clamp. Thanks
I

 

[luckydoll09]

I want order the full kit please…..PM you…Thanks

 

[Trailgomer]

My kit arrived today and is a giant improvement over the stock setup!
Thank you sir!

 

[Landdwnundr]

I would like a full kit, please send ordering info

 

[Bbulkley18]

Hey, I’d like a full kit as well if you could message me ordering info. Thanks!

 

[Envo]

I'll take a full kit when available please.

 

[EleventhHour]

I would like a full kit please. This is such an awesome idea!

 

[retvr39]

Would like a full kit with the aluminum sleeve if you still have one.
Thanks

 

[captancrunch]

I am interested in complete kit. just searched and found your post. What payment options do you except?

 

[BLEE]

I'd like the full kit, as well. TIA.