CZ 457

#2,401
Stev0 said:
I hope you realize that's a phony store.
Click to expand...
No I did not and really don’t think that’s on me to investigate and verify. My point is that they are available unless you are looking for a unicorn.

Here, for the Google impaired:

GunsAmerica | Buy Guns Online and Sell Guns Online

Buy and sell guns online at GunsAmerica.
www.gunsamerica.com www.gunsamerica.com

www.area419.com

CZ 457 MTR - Fully Loaded

NOTE: IF YOU ORDER THIS PRODUCT YOU WILL NEED TO SUBMIT AN FFL FOR SHIPMENT. WE WILL ONLY SHIP TO FFLs, PLEASE SEND A COPY OF FFL TO [email protected] FOR QUICKEST SHIPPING. Unfortunately these are very limited quantities for us, and we expect these to sell out quickly. If you have received a...
www.area419.com www.area419.com

Or are these fake too? 😎
 
  • Like
Reactions: WeeHooker
#2,404
lash said:
No I did not and really don’t think that’s on me to investigate and verify. My point is that they are available unless you are looking for a unicorn.

Here, for the Google impaired:

GunsAmerica | Buy Guns Online and Sell Guns Online

Buy and sell guns online at GunsAmerica.
www.gunsamerica.com www.gunsamerica.com

www.area419.com

CZ 457 MTR - Fully Loaded

NOTE: IF YOU ORDER THIS PRODUCT YOU WILL NEED TO SUBMIT AN FFL FOR SHIPMENT. WE WILL ONLY SHIP TO FFLs, PLEASE SEND A COPY OF FFL TO [email protected] FOR QUICKEST SHIPPING. Unfortunately these are very limited quantities for us, and we expect these to sell out quickly. If you have received a...
www.area419.com www.area419.com

Or are these fake too? 😎
Click to expand...
I don't really think that's on me to investigate. Did you even read what I wrote? I hope You realize it's a phony store. I was trying to help you out & you decide to be a dick.
 
Last edited:
  • Haha
  • Like
Reactions: crwnking steve, AirgunnerPCP, gunjunkie45 and 1 other person
#2,408
  • Like
  • Haha
Reactions: MCSO1357, Sniperwannabee and adubeau
#2,409
spentbrass1 said:
Does anyone know when CZ will be producing new barrels or rifles seems they have stopped supplying them to dealers
Click to expand...
What specifically are you looking for? It's my experience that CZ shipments of 457 rifles and barrels seem to come in waves of relatively small lots. One model at a time. When they do show, there is usually a backlog of folks waiting to purchase and they go within days. ( Local dealer almost never get a chance to grab them.) I've signed up for in stock notices with several online CZ dealers and hardly a week goes by that something doesn't go in ( and out) of stock.
 
  • Like
Reactions: lash
#2,410
  • Like
Reactions: VNK971 and lash
#2,413
J_D said:
Finally got my new 20" Lilja barrel installed to match my other rifle with the 16", along with the Timney trigger.

Install was very simple for both. Starting with the recommended .043" headspace to begin with.
Click to expand...
Just a heads up, I had major fail to extract issues, called Lilja and they recommended I go down to .041 on the headspace. That worked perfectly.

That barrel is incredible with CX from the lot I tested.
 
  • Like
Reactions: fredfish, lil'skeet and WeeHooker
#2,414
My 457, really accurate with SK Pistol Match.
I use it NRL/PRS style matches here in the UK.

304852338_672723560945679_7035853649323611878_n.jpg
304891663_672723834278985_897198173828908801_n.jpg
303044500_672724154278953_202075949516317309_n.jpg
 
  • Like
Reactions: gpkon66, Devlin, RTESantaFe and 4 others
#2,416
WeeHooker said:
The 16.5" At-One models are pretty common. You can find that gun for over $100 less if you know where to look. I paid $620 OTD for a new 24" AT1 last month. Try gundeals.com
Click to expand...
I think I paid about the same for my 24" version too. Did some searching and found the gun dock had em. I *thought* I was getting a 20" rifle, but... I'll probably switch the barrel out at some point.

The KRG chassis should be here in a few days. Found that the At One isn't quite the right tool for the PRS job

M
 
  • Like
Reactions: WeeHooker
#2,423
yogibearal said:
Nice looking build, very few builds here based on the LRP version. Thinking of doing something with my LRP as well. What chassis is that you are using? Noticed it has an integrated ARCA rail on it.
Click to expand...
It's a Chassis made in the Uk.
Not sure if he exports.
Not sure if I can post a link within the rules?
It's made by R and F sporting supplies. in the UK.
 
#2,424
Anyone run into eye relief issues on their setups? My 457 in a KRG bravo with a Gen 1 5-20 Vortex Razor on an Area 419 mount has me scrunched way back when I'm shooting from the prone. Even with the scope pushed as far forward in the rings and with the rings set as far forward on the rail as possible.

I plan on replacing this scope anyhow since I just pulled it off my 6.5 for the time, anyone got some suggestions for something shorter or with more forgiving eye relief?
 
#2,425
MRDRFCKR said:
Anyone run into eye relief issues on their setups? My 457 in a KRG bravo with a Gen 1 5-20 Vortex Razor on an Area 419 mount has me scrunched way back when I'm shooting from the prone. Even with the scope pushed as far forward in the rings and with the rings set as far forward on the rail as possible.

I plan on replacing this scope anyhow since I just pulled it off my 6.5 for the time, anyone got some suggestions for something shorter or with more forgiving eye relief?
Click to expand...
Can you get some butt plate spacers for the chassis
 
#2,429
MRDRFCKR said:
Anyone run into eye relief issues on their setups? My 457 in a KRG bravo with a Gen 1 5-20 Vortex Razor on an Area 419 mount has me scrunched way back when I'm shooting from the prone. Even with the scope pushed as far forward in the rings and with the rings set as far forward on the rail as possible.

I plan on replacing this scope anyhow since I just pulled it off my 6.5 for the time, anyone got some suggestions for something shorter or with more forgiving eye relief?
Click to expand...
It's normal for prone to need the butt plate moved out ~3/4" or so from a positional setting. Your head is naturally closer to the scope in prone vs positional.
 
  • Like
Reactions: lash
#2,430
MRDRFCKR said:
Anyone run into eye relief issues on their setups? My 457 in a KRG bravo with a Gen 1 5-20 Vortex Razor on an Area 419 mount has me scrunched way back when I'm shooting from the prone. Even with the scope pushed as far forward in the rings and with the rings set as far forward on the rail as possible.

I plan on replacing this scope anyhow since I just pulled it off my 6.5 for the time, anyone got some suggestions for something shorter or with more forgiving eye relief?
Click to expand...
Use an extended scope mount instead of individual rings.
 
  • Like
Reactions: lil'skeet, WeeHooker and Sniperwannabee
#2,431
MRDRFCKR said:
Anyone run into eye relief issues on their setups? My 457 in a KRG bravo with a Gen 1 5-20 Vortex Razor on an Area 419 mount has me scrunched way back when I'm shooting from the prone. Even with the scope pushed as far forward in the rings and with the rings set as far forward on the rail as possible.
Click to expand...

Am not familiar with the Area419 but have a Murphy rail which is extended 1.5", also have the Nightforce cantilever Unimount. This setup works for me using the Vortex Strike Eagle 5-25x56 and KRG Bravo chassis.
 
  • Like
Reactions: lash
#2,438
Frankr said:
Random question.


Has anyone taken and stoned the bottom of the bolt to get rid of the engraved numbers to see if it smooths up the action?

Winter time tinkering. I love the 457 and all the improvements but I still think it’s not as smooth as the 452/455 actions because of this.

It doesn’t impact how the gun shoots or cycles really, just a little pet peeve.
Click to expand...
Yes, first thing I did as soon as I racked the bolt. It was really horrible. I had a fine stone and it slicked it up beautifully.
 
  • Like
Reactions: VNK971 and Frankr
#2,440
obviousfakename said:
I took my new CZ 457 out for the second time today. This is my first long gun and I couldn't be happier.

Clearly I'm the weakest part of this setup, but these are my best and worst groups at 50y and 100y, all with Wolf Match Target.

View attachment 7965681
View attachment 7965679View attachment 7965680View attachment 7965682View attachment 7965683
Click to expand...
It’sa great Rifle. Try some SK std plus or rifle match in it if you can get some. Plus you will get better with it as you both get broken in a bit.
 
Last edited:
  • Like
Reactions: obviousfakename
#2,442
What could go wrong?
Was getting ready for a range trip and commented that my kit, ( Lilja barrel ) was not shooting a well as I was used to ( .5 MOA or better). Before I knew it "they" started to clean the rifle and ran a rod, jag, minus a patch through the barrel. They mentioned it had to be dirty as it was tough to push through the patchless rod and jag. Theoretically it should be fine, the jag and patch together are a lesser diameter then the barrel. I don't have a scope and haven't been able to shoot it. Still worried it damaged the barrel. I will clean it myself ( Boretech rod and jags) on Sunday. Hoping for the best. Thoughts?
regards, pete
 
#2,443
Greedus said:
What could go wrong?
Was getting ready for a range trip and commented that my kit, ( Lilja barrel ) was not shooting a well as I was used to ( .5 MOA or better). Before I knew it "they" started to clean the rifle and ran a rod, jag, minus a patch through the barrel. They mentioned it had to be dirty as it was tough to push through the patchless rod and jag. Theoretically it should be fine, the jag and patch together are a lesser diameter then the barrel. I don't have a scope and haven't been able to shoot it. Still worried it damaged the barrel. I will clean it myself ( Boretech rod and jags) on Sunday. Hoping for the best. Thoughts?
regards, pete
Click to expand...
You might want to read this article on cleaning 22LR precision barrels and stop using the rod. I would buy a $50 Teslong scope from amazon, it's a cheap tool to work on your $550 barrel and stop guessing why the POI accuracy falls off.. Have fun in keeping the chamber clean. https://www.thetruthaboutguns.com/a-guide-to-22lr-barrel-care-for-the-precision-rimfire-shooter/
 
  • Like
Reactions: MCSO1357 and WeeHooker
#2,444
Greedus said:
What could go wrong?
Was getting ready for a range trip and commented that my kit, ( Lilja barrel ) was not shooting a well as I was used to ( .5 MOA or better). Before I knew it "they" started to clean the rifle and ran a rod, jag, minus a patch through the barrel. They mentioned it had to be dirty as it was tough to push through the patchless rod and jag. Theoretically it should be fine, the jag and patch together are a lesser diameter then the barrel. I don't have a scope and haven't been able to shoot it. Still worried it damaged the barrel. I will clean it myself ( Boretech rod and jags) on Sunday. Hoping for the best. Thoughts?
regards, pete
Click to expand...
Seriously? A jag without a patch and its tight in the barrel? Was this done dry without cleaning solution (no patch to hold solvent)?

Who is “ they”?

And why are you letting other people clean Your rifle? I use a .20 caliber rod and jag combo for all my 22s, but I prefer to use a patchworm pull through set up with felt pellets…….hmmm, hold on a sec.

Eh, nevermind, gotta be phishing post and I got suckered. Look forward to hearing about your next cleaning session involving a hi speed drill motor with brass and stainless brushes
 
  • Like
  • Haha
Reactions: Smallcalshooter, Papa Mike, lil'skeet and 4 others
#2,445
Good morning. Yes, a jag with no patch and completely dry. He said it was tight and had to push it through. "they" are a friend just getting into PRS. I previously walked them through cleaning barrel including soaking and brushing chamber. He is new to the process and I had to run an errand while he put gear and kit together for the range. Wasn't as if I was leaving kids behind with a stranger, but yeah, sorta feels that way now. As reference, I use the BoreTech rimfire specific rod and jags and cotton patches with Rimfire Blend clear and C4 carbon cleaner.

regards,
 
Last edited:
#2,446
Greedus said:
Good morning. Yes, a jag with no patch and completely dry. He said it was tight and had to push it through. "they" are a friend just getting into PRS. I previously walked them through cleaning barrel including soaking and brushing chamber. He is knew to the process and I had to run an errand while he put gear and kit together for the range. Wasn't as if I was leaving kids behind with a stranger, but yeah, sorta feels that way now. As reference, I use the BoreTech rimfire specific rod and jags and cotton patches with Rimfire Blend clear and C4 carbon cleaner.

regards,
Click to expand...
Anything is possible but I doubt one treatment of a soft jagg material on a hardened steel barrel with destroy it. That said, the only way to see if there is damage is to reclean it properly and : a) scope the bore and/or b) shoot the rifle. Everything else is just speculation and worry for naught.
 
  • Like
Reactions: lil'skeet
#2,447
Talked myself into a KRG Bravo for the (formerly) At-One a few weeks ago. Still haven't shot it yet. Was supposed to go today, but a freaking headache did me in. Heachache seems to have abated some, so I'm likely to go tomorrow.

Need to figure out an ARCA rail for this rifle. The extra-wide base makes the wobble go down while on barricades. The very nice KRG version has a beveled edge, but that's easy enough to do on a bench grinder.

The nice part about shooting .22 is that you can send a lot of rounds downrange without the cost of my 6.5 Creedmore

M
 
  • Like
Reactions: WeeHooker
#2,448
WeeHooker said:
Anything is possible but I doubt one treatment of a soft jagg material on a hardened steel barrel with destroy it. That said, the only way to see if there is damage is to reclean it properly and : a) scope the bore and/or b) shoot the rifle. Everything else is just speculation and worry for naught.
Click to expand...
I am thinking the same. Hope to get to the range in a a couple weeks. I will keep the kit the same and use same ammo (SK Rifle Match).
Will post then.
regards,
 
#2,449
mikeshaw2 said:
Talked myself into a KRG Bravo for the (formerly) At-One a few weeks ago. Still haven't shot it yet. Was supposed to go today, but a freaking headache did me in. Heachache seems to have abated some, so I'm likely to go tomorrow.

Need to figure out an ARCA rail for this rifle. The extra-wide base makes the wobble go down while on barricades. The very nice KRG version has a beveled edge, but that's easy enough to do on a bench grinder.

The nice part about shooting .22 is that you can send a lot of rounds downrange without the cost of my 6.5 Creedmore

M
Click to expand...
I have Bravo chassis and was fortunate to find a used KRG Arca rail, The fit is spot on, and well made. Definitely solid and as such, the attachment process is more involved. Other makes may be a simpler install, though I would follow the KRG instruction to ensure it's on there right.
regards,
 
  • Like
Reactions: WeeHooker
#2,450
Quick question for whoever can answer. I picked up a 457 with a 20” heavy barrel but not sure if it’s just the varmint or the mtr? It’s just the barreled action so the stock not being there isn’t helping me ID which one it is…. Help?
 
You must log in or register to reply here.

Similar threads

Mark_Dorman
How to get the CZ 457 Manners TCS Stock
Replies
31
Views
9K
Malum Prohibitum
Malum Prohibitum
exacto
SOLD NEW CZ-USA 457 MDT ACC VARMINT PRECISION 22 LR
Replies
4
Views
1K
USMC22
U
The4GunGuy
SOLD SOLD SOLD SOLD: MDT ACC Chassis for CZ 457
Replies
0
Views
887
The4GunGuy
The4GunGuy
kg232
Rimfire Trades added - CZ 457 MTR
Replies
7
Views
3K
kg232
kg232
T
7X300WM- Heavy Bolt Lift only on Fire Formed - Need to Neck Turn?
Replies
9
Views
723
Maurygold
M
Top Bottom
Back
Home
Forums
Merch
Alerts