This thing is suhweeeet! Nice rifle tui_man!
My new alround shooter to put the hunting back into shooting.
-
Having trouble using the site?
Contact support
precision rifles... show em
- Thread starter redneckbmxer24
- Start date
Nice. By the way, what made you pick the 6.5x47 over the 6.5 Creedmoor, for instance?
Sent from my GT-S6810P using Tapatalk
. 
Finally had some decent weather yesterday. Not so much today.
How short is that barrel?
Sent from my GT-S6810P using Tapatalk
Obviously nothing fancy, and the groups shown below are not spectacular, but the good thing is that this rifle shoots a 65gr Sierra GameKing load that was developed for my AR-15 solidly into 0.75-moa out to 600 yards. Thus, I can prepare the load in bulk and use in either rifle, whether for hunting or for informal practice.
8 shots from 200 yards:
5 shots from 600 yards:
not sure actually... it was a gift years ago.... it has "PWS-P" stamped on the barrel... i'm told that stamp stands for Precision Weapons Shop... i'm going to sell this weapon too, as it has never been fired and sitting in my safe for years.. anyone interested can PM me or email me at [email protected]....
barrel is stamped: "PWS" (precision weapons shop)
the weapon was a gift years ago.. i believe GA Precision was the builder
the weapon was a gift years ago.. i believe GA Precision was the builder
Another of mine.
Accurate Ordnance built 6mm Creedmoor
Stiller Tac30 action
Stiller 20moa mount
Brux 1-7.5 AO varment Contour finished at 24" with a blended Little Bastard brake
Timney 510 set at 1lb 0.8oz
Manners T5a with Badger M5 (I had the stock before they built it but they made a few adjustments on it)
NF Rings
March FX 5-40x56 or Steiner 5-25x56
Atlas Bipod
Shoots in the low 1's easily but I'm not a paper puncher but it is an awesome gun built by some awesome guys.
Accurate Ordnance built 6mm Creedmoor
Stiller Tac30 action
Stiller 20moa mount
Brux 1-7.5 AO varment Contour finished at 24" with a blended Little Bastard brake
Timney 510 set at 1lb 0.8oz
Manners T5a with Badger M5 (I had the stock before they built it but they made a few adjustments on it)
NF Rings
March FX 5-40x56 or Steiner 5-25x56
Atlas Bipod
Shoots in the low 1's easily but I'm not a paper puncher but it is an awesome gun built by some awesome guys.
Mauser 98 build
I wanted to make a replica FNH TSR XP
<a href="http://s800.photobucket.com/user/Chaseerickson12/media/Mobile%20Uploads/0162CB5E-5D8E-4F08-8F23-BB5A8F1A6248_zpsdcbvjfl8.jpg.html" target="_blank"><img src="http://i800.photobucket.com/albums/yy283/Chaseerickson12/Mobile%20Uploads/0162CB5E-5D8E-4F08-8F23-BB5A8F1A6248_zpsdcbvjfl8.jpg" border="0" alt=" photo 0162CB5E-5D8E-4F08-8F23-BB5A8F1A6248_zpsdcbvjfl8.jpg"/></a>
I wanted to make a replica FNH TSR XP
<a href="http://s800.photobucket.com/user/Chaseerickson12/media/Mobile%20Uploads/0162CB5E-5D8E-4F08-8F23-BB5A8F1A6248_zpsdcbvjfl8.jpg.html" target="_blank"><img src="http://i800.photobucket.com/albums/yy283/Chaseerickson12/Mobile%20Uploads/0162CB5E-5D8E-4F08-8F23-BB5A8F1A6248_zpsdcbvjfl8.jpg" border="0" alt=" photo 0162CB5E-5D8E-4F08-8F23-BB5A8F1A6248_zpsdcbvjfl8.jpg"/></a>
Finally I can post here!!
GAP rifle built on a Surgeon 591R
16" Bartlien 1:12 Palma
AICS 2.0 switching to the McMillan A-5 w/ surgeon DBM
Jewell trigger
SureFire brake
Atlas bipod mounted via BT15 rail (waiting to be delivered)
Sorry for the crappy cell phone pics
GAP rifle built on a Surgeon 591R
16" Bartlien 1:12 Palma
AICS 2.0 switching to the McMillan A-5 w/ surgeon DBM
Jewell trigger
SureFire brake
Atlas bipod mounted via BT15 rail (waiting to be delivered)
Sorry for the crappy cell phone pics
I wonder when the woman that won the usmc raffle will post hers here...
Sent from my DROID RAZR using Tapatalk
Sent from my DROID RAZR using Tapatalk
What stock is that Drifter™? The look is elegant and simple, I really like it...
Stock came from Numrich.
Link: Stock, Short Action, BDL, Heavy Barrel Varmint, Satin Finished Walnut Gun Parts | 553690 | Numrich Gun Parts
The aged factory finish was a little discolored, but the wood itself was in excellent shape. So it was stripped and refinished, and forend tip was reshaped (rounded). I think this stock is sometimes used on M40-type clones.
My Surgeon/ Jae with 6.5 creed barrel , Proof Research 308 barrel , March 5-40x56 FFP and also have surgeon 223 bolt and 223 barrel getting spun shortly for it.
Bro, how's the Proof barrel working for you?
Mark
I actually haven't shot it much since I just got it. I love it, shoots .25 Moa easy at 100yrds. It's mtu contour but feels more like rem varmint.
my rifle
Here's my Defiant action, KMW stocked, Proof 300wm barreled machine. 29" 1/17 twist shooting short 171 gr tungsten cored bullets at 3450f/s. Pretty much a laser. Using an older Premier scope with H37 reticle...I never turn a turret only hold a little bit.
R/Mark
Here's my Defiant action, KMW stocked, Proof 300wm barreled machine. 29" 1/17 twist shooting short 171 gr tungsten cored bullets at 3450f/s. Pretty much a laser. Using an older Premier scope with H37 reticle...I never turn a turret only hold a little bit.
R/Mark
Attachments
Last edited:
This is my newest build and my first post. I have been using this site for years and am grateful for all of your guys knowledge. I hope I can add in some way. About the rig, the barreled action was done by Ed Sweet out of Idaho and I worked it over to my specs. Branden did the paint of course and I just added the bushy and the Larue a few days ago. This was my first time using a Sako action but so far it has been running great. Chambered in 7 Mag running 180gr HVLD's and 180 Hybrid's
Attachments
Last edited:
here's my addition, took a while to accumulate all the parts as this is a super rare long range build using only the best components. this is a bad mother fucker and I'm quite proud of it. Below is the target from when i got it out to zero, shot at 50 yards off of a backpack backpack. If thats not precision rifle than i dont know what is
This has got to win the "Operator as Fuck" award!
Front to back
1. 300wm built by Louisiana Precision
1086 surgeon action
Krieger 1-10 rem varm
Manners T5-A chassis painted by Shortbus
S&B 3-20 H59
TBAC 338BA
2. 280 ackley built by Tumbleweed rifles
Stiller TAC300 with ptg canoe bottom metal (5+1)
Rock 1-8.75 rem varm
Manners T3
Nightforce f1 mlr2
TBAC 30BA
3. 260 win Surgeon scalpel
Surgeon 591
Krieger 1-8 heavy Palma fluted
J Allen chassis
S&B 5-25 H2CMR
TBAC 30p-1
Thanks. It was a very simple refinish that I've used numerous times. The older the wood, the better the results.
As previously mentioned, I removed the original finish (using a chemical stripper), then lightly sanded the wood.
Fairtrimmer's Military Ox was used first, followed by Tom's 1/3 Mix (wax).
The results are a very natural subdued oil finish, similar to older wood military stocks.
Last edited:
Beautiful rifles. I'm green with envy.
Front to back
1. 300wm built by Louisiana Precision
1086 surgeon action
Krieger 1-10 rem varm
Manners T5-A chassis painted by Shortbus
S&B 3-20 H59
TBAC 338BA
2. 280 ackley built by Tumbleweed rifles
Stiller TAC300 with ptg canoe bottom metal (5+1)
Rock 1-8.75 rem varm
Manners T3
Nightforce f1 mlr2
TBAC 30BA
3. 260 win Surgeon scalpel
Surgeon 591
Krieger 1-8 heavy Palma fluted
J Allen chassis
S&B 5-25 H2CMR
TBAC 30p-1
Built this rifle about 7 mos ago and have had it out to 980yds so far. I can hit my 13" gong at 800 yds with boring consistency. This rifle will shoot 1/4 MOA @ 200 yds all day long and for everything I've read about Mausers ( especially one in this previous condition) that is "impossible". I built this gun in part to disprove the naysayers, even a friend who is a gunsmith and who is now building 2 6.5-284 rifles on Mauser actions. I have got about $2k in this rifle, $850 of which are the scope.
I currently have a Sightron SIII 8-32x56 LRMOA scope on it and have since made the cheek rest adjustable.
1909 Argentine Mauser action - drilled, tapped and blueprinted by Ron Nichols
Swedish bolt stop w German ejector
bent bolt - by me
Tac knob
smooth shroud
Timney featherweight deluxe trigger
Mark X cocking piece - shortened lock length to 3/8"
Tubb speedlock firing pin and spring
Lothar Walther 6.5x55 barrel - finish chambered, target crowned and cal stamped by Ron Nichols
EGW 20moa scope base
Warne 30mm scope rings
permanent scope will be Sightron SIII 8-32x56
Cerakote by AEC (forest green, dark earth)
FA Enterprises stock
Caldwell pivot bi-pod
fitting, bedding and assembly - by me
I currently have a Sightron SIII 8-32x56 LRMOA scope on it and have since made the cheek rest adjustable.
1909 Argentine Mauser action - drilled, tapped and blueprinted by Ron Nichols
Swedish bolt stop w German ejector
bent bolt - by me
Tac knob
smooth shroud
Timney featherweight deluxe trigger
Mark X cocking piece - shortened lock length to 3/8"
Tubb speedlock firing pin and spring
Lothar Walther 6.5x55 barrel - finish chambered, target crowned and cal stamped by Ron Nichols
EGW 20moa scope base
Warne 30mm scope rings
permanent scope will be Sightron SIII 8-32x56
Cerakote by AEC (forest green, dark earth)
FA Enterprises stock
Caldwell pivot bi-pod
fitting, bedding and assembly - by me
New .260 Remington. 24" MTU Douglas barrel, Aics with Viper Skins, vortex viper PST 6x24x50. Shot it out to 800 so far with very impressive results
finally all painted up and shooting. LRI 6.5CM
the target is 200yds. (corrected after first shot)
I am very happy with it
the target is 200yds. (corrected after first shot)
I am very happy with it
finally all painted up and shooting. LRI 6.5CM
the target is 200yds. (corrected after first shot)
I am very happy with it
Which cat tail are you using? Nice rifle btw.
It's the vortex. I have a MGM on my ar and like this one better because the lever is a little shorter
Here you go Colcalcipherol.
That XLR/Stiller is pretty sweet. Is it a 408 or 375 CT? Specs please.
Justin
PSS 300win, 5.5-22x NF with all bells and whistles, PT&G bottom metal for AICS mags on the way, T5. Needs bedding, bolt knob and Brake done.
Started as this:
AIAE MK1 with HDMR
Theres a R&D precision 243 being built and a GAP 6.5 Creed too. I should have a LMT MWS soon too. Once I move next year from CA ill be buying: AI AT 308 and 300win, GAP10, DTA SRS-A1 and DTA HTA. I wish I never traded my DTA.......
Started as this:
AIAE MK1 with HDMR
Theres a R&D precision 243 being built and a GAP 6.5 Creed too. I should have a LMT MWS soon too. Once I move next year from CA ill be buying: AI AT 308 and 300win, GAP10, DTA SRS-A1 and DTA HTA. I wish I never traded my DTA.......
Last edited:
Here you go Colcalcipherol.
That XLR/Stiller is pretty sweet. Is it a 408 or 375 CT? Specs please.
Justin
Specs, sure then tell me how you got the picture to appear. This was my first attempt and the only thing that showed up was the link . . .
.375 CheyTac
Stiller .408 action
4-Port Muscle Brake
Proof Research barrel, 1/10.5 twist
LRA bipod
Steiner 5-25x56 MSR
Cerakote by Michael Ware at Controlled Chaos Arms
