That's something I havent thought about. I think something is off about mine.
-
Having trouble using the site?
Contact support
That's something I havent thought about. I think something is off about mine.
I just put a Krieger on mine and love it....
I got a 26" bull with a 7.5 twist off the shelf because I didn't want to wait months for it...
Had one thing to adapt too that I didn't like at first...but like it better after I found mags I could fit 2.85 in...
I have a pic bubble that hangs off the side to level the rifle. Then I have a separate bubble that I can sit on top of the turret. When I level everything out, my eye sees the reticle being off by maybe a hair. I have yet to take it somewhere that I can reference the reticle against to make sure its level.
I'm going to pick up a Knights Armament level and see if that is any better.
The only true way to tell is to level the Reticle to plumb line and then go with it. I’ve got the anarchy outdoors 20 moa scope base awaiting shipment. Hoping it’s higher quality.
I just received my ambidextrous safety switch and custom engraved titanium shroud from them. Great customer service and they shipped fast. I was eyeballing that same rail with the bubble but I'm more inclined to buy that add on bubble level and sit it right under my scope.
Gamedic your better off with the level set up under the scope. I bought a Vortex level that mounts on my Razor. I can’t see it when I’m looking through the scope. I have to move my head out to see it. I noticed this at my first match last week when I had to shoot of a large tractor tire. I laid down with my rifle stretched across the tire. The shot was over 500 yds and I couldn’t see the level. I was shooting at a KYL rack. I hit the first three but missed the last two both times through. After shooting I got up and seen my level was pegged to the right. I got to rethink this...
That's what I was thinking as well. The level I put on my turret is just a simple level that I set on the scope to make sure everything is balanced and then take it off.
I have the same issue and just started practicing to keep the butt pad in my shoulder at the same angle to keep the rifle uncanted. This way I don’t have to rely on a level. You could look into a Spuhr Mount, a Send It LED level, or the new AO base rail with level. I use a Spuhr Mount so it has the included level in the mount.
Today took some pics of my 223 of the gun and mag. The front top of the mags are touching the bottom of the barrel?
That is why it is so hard to sit the mags. I thought may be the gun is out of spec but then I look at my RPR 6.5 it sticks up into the mag well just the same.
So are the mags out of spec? If I Dremel off a bit off the lip they should be fine? But what if I use steel mags? It is much harder to remove material, and it might not be a good idea? So who makes a good steel mag for this? I think it is AICS style?
I am trying to see whether I can just do some Dremel work or send it back.
That is why it is so hard to sit the mags. I thought may be the gun is out of spec but then I look at my RPR 6.5 it sticks up into the mag well just the same.
So are the mags out of spec? If I Dremel off a bit off the lip they should be fine? But what if I use steel mags? It is much harder to remove material, and it might not be a good idea? So who makes a good steel mag for this? I think it is AICS style?
I am trying to see whether I can just do some Dremel work or send it back.
Last edited:
Got off shift today and rushed home to throw a few parts on. AO ambidextrous safety, CTK mag release, Timney trigger set at 8oz/1lb, Witt Machine muzzle break, and my AO laser engraved titanium shroud.
If anyone needs a factory trigger, aluminum bolt shroud, or muzzle break I have them and will be happy to ship them out free of charge.
Yesterday I bought a brick of Federal Gold Medal 210 Match primers. I loaded up a five pack of Berger 105 VLD target, 42 grain of H4350, GM210M with Hornady neck sized only brass. This combo shot really good at 400 yards. I was calling this load my match load. According to BallisticsARC and my scope dial the load is around 3000 FPS.
good group!
Yesterday I had bought a box of Hornady 105 HPBT Match bullets to try due to cost vs the Bergers. About 13-15 dollars a box cheaper. I figured these to be my practice ammo if they worked out.
So today I loaded up five Hornady 105 BTHP, 42 grains of H4350, GM 210M and neck sized Hornady brass. I shot them at 400 yds. I figured 3000 FPS. I took a photo of the group. Aiming at the white dot. It appears they are a little faster than 3000 FPS with 1.5 on my scope.
I think I just found me a new bullet. I also believe the Federal GM210m primers are the go to primer for this combo.
good group!
Yesterday I had bought a box of Hornady 105 HPBT Match bullets to try due to cost vs the Bergers. About 13-15 dollars a box cheaper. I figured these to be my practice ammo if they worked out.
So today I loaded up five Hornady 105 BTHP, 42 grains of H4350, GM 210M and neck sized Hornady brass. I shot them at 400 yds. I figured 3000 FPS. I took a photo of the group. Aiming at the white dot. It appears they are a little faster than 3000 FPS with 1.5 on my scope.
I think I just found me a new bullet. I also believe the Federal GM210m primers are the go to primer for this combo.
Attachments
Damn, that's impressive @ 400 yards I might have to grab a box and give them a go.
Nice shootin netman
Nice shootin netman
If that's the best you can do at 400 yrds...you are gonna have to tighten up or you're off the team...
Nice work....looks like you may have found your go to....looks good
Nice work....looks like you may have found your go to....looks good
SP3R V3 handguard showed up today. Gotta wait for my new barrel before it goes on. Hoping to shoot it this week sometime.
Gonna be pretty while collecting dust sitting in this box waiting for the new barrel. Only want to disassemble the rifle once. Also need to order an MLOK pic rail for when the new bipod comes in.
The last two parts left to order before this build will be done are the Atlas bipod and Krieger barrel. Once everything is in, I'll disassemble it, send parts for Cerakote, and when everything is done final assembly will happen.
Decided to get creative and make a cheek pad from foam sheets. I'll know how v1.0 goes Wednesday.
Cool. Post a pic. I always use the soft side of the adhesive-backed Velcro. It can get cold enough here in upstate NY that your cheek freezes to the riser!
Has anyone mounted a MK5 5-25x56 on a 6mm Creedmoor? I'm looking at the Vortex/ Seekins rings and would like to go as low as possible, but I don't think the .95's will work.
I don’t think .95 rings will work with a 56mm objective. I personally went with a 1.5 in. mount for a 50 mm objective so I wouldn’t have to smash my face on the cheek rest to get a proper eye alignment. You can probably get away with using 1.26 in. rings without using lens covers. Most people I’ve talked with that have 56mm optics are using 1.5 in. rings/mount on their RPR. Hope this helps you out. My buddy uses a 1.5 in. spuhr on his RPR with a 56mm Bushnell.
+1 for the AR height.
I run 1.46 Seekins rings with a 56mm on mine. I also use Tenebraex covers without an issue.
I run 1.46 Seekins rings with a 56mm on mine. I also use Tenebraex covers without an issue.
My Area 419 ARCA rail arrived a short time ago. Got it mounted to the stock forearm effortlessly. Thought I would take a few pictures for all to see. Got my Harris bipod on the way. I’ll order the ARCA slide to marry the two next week.
Attachments
For you guys interested in a Timney trigger dvor.com has the curved trigger on sale for $159.
I’ve never had good luck with dvor. I think anarchy outdoors has a post super bowl sale going on for 12% off anything in their store. Very helpful people and great customer service. My first 2 upgrades to my RPR were a 2 stage timney flat shoe trigger and a 40 moa rail from AO.
All you guys that want to use the lowest rings need to keep in mind the stock on the RPR is almost the same plane as the rail. Going low can means you have no comb adjustment.
I went with the 308 mine only had the 20 in barrel option 1/10 twist to start its cheap fun and great to learn with and at the time was under 1k hoping something 6.5 is next its hard to say so many choices ....or if i start reloading 260 rem.
This is a great way to start. I started out with a rem 700 in .308. After a couple years I bought a RPR in 6.5. Now I’m building on a custom action with changeable calibers. I highly recommend a 6mm variant, whether it be a 6.5 creed or a 6mm creed. When I burn out my RPR 6.5 I’ll probably rebarrel to a 6mm creed. Have fun with that .308. I still love to shoot mine.
The factory base are also not a true 20 moa base the range from 12 - 15 moa last time to measured a few.
I finally got this lovely lady all put back together. Time to hit the range if it ever stops snowing.
