So about a year or so ago, I was doing velocity loads on different bullets for 308 Winchester. I was using virgin Winchester 308 brass so finally about 90 pieces. I decided to clean them and prep them for another firing at the same time I had some IMI 308 ball cases, and there were approximately 100 round to do this which I cleaned at the same time.

The IMI military brass was great , the pockets were not crimped but it took some pressure with my RCBS primer tool to seat them. Unfortunately when priming the once fire 308 win cases the primers went in with very minimal resistance in all the cases.

Thinking about it some of the top end ladder loads might have been a little warm. but most of them were with AR COMP or Reloader 17. With the Re 17 it seems you just can’t fit enough powder in the case to over pressure them . After I go done I started thinking these will not work out well in my gas gun.

So these 80 cases will go to loads for my bolt loads. But this does not give me a warm fuzzy about this brass. I have another 150 or so of these. I’m thinking of reloading I should go to SRP either Peterson or Alpha munitions brass.

All prices include shipping.

If paying by check, it must clear before shipping. I have PayPal and Venmo ,you cover fee if you chose secure PayPal.

Happy to take more photos,text,call,etc


McMillan Game Warden carbon fiber stock LA, 700, cut for M5 bottom metal, M24 barrel channel,never been used $500 SOLD








$650 if you want the grayboe floor plate and Wyatt’s mag kit with it


Grayboe M5 floor plate LA
Never used or installed but small pin prick sized ding (silver dot in photo)
$150.SOLD

Wyatt’s internal max box kit
NIP part # WY-BOX-KIT-MBE2-LA
$60SOLD





Choate tactical stock R700 LA

Aluminum bedding block

DBM bottom metal,action screws

SOLD $160 SOLD

22GT Brand new, all same lot. 600 shipped for all 500 pieces, so save 75 bucks and shipping on it.

MDT Ckyepod PRS - $425 ( top one) sold
MDT Ckyepod Gen II w/ ARMs 17 adapter (ready for whever clamp you want) - $450 shipped
Garmin FORETREX 901 - unit only, barely used. $450 dollars shipped


PP F&F, Venmo, or Zelle

In October I began building a Tikka 7PRC. I was back and forth between chassis as this was my first custom build. Building my 7PRC for hunting, looked at the HNT26 and saw that @MDT_OFFICIAL does not make a polymer magazine in 7PRC for their hunting chassis. I reached out via phone and talked with a couple guys, told them exactly what I was doing and what I was thinking. They told my that a 3rd Polymer magazine was in the works, so I pulled the trigger on the HNT26. I knew I would have to shoot with the 5rd AICS for a while. Finally have my build dialed in. As a hunting rifle (scope mounted) minus my AICS mag I'm ay 7lbs 14oz. Right were I wanted to be.

Today I got the email the magazine was finally available. MDT 7PRC 3rd Polymer mag. $50...does NOT work with the Tikka LA. WTF...

I'm going to have to hunt it this year, but end of the season I'll have to go to another company. I just cant fathom how MDT left the Tikka shooters out on this one. Maybe I'm naive.

UBR2
$140. Shipped

Just received a long awaited 7PRC prefit from a reputable vendor here.

Prefit for a Curtis Axiom LA previously wearing a 300WM tube from MPA

Forster FL bushing die

New Nosler brass.

I DONT have a go gauge yet, they are all on backorder. its on the way.
I DONT have factory ammo in hand yet, but will try that tonight.

After mounting up the new barrel with a quality torque wrench and appropriate high-presure synthetic grease, I've got an issue.

Dropping fresh brass into the raceway, bolt will close with reasonable pressure.

After running same brass through the FL die to uniform them prior to loading, bolt will only close with a hard push. Enough of a push that to roll the rifle over on a bipod. Enough of a push you can't run the bolt. All the resistance comes in the last 1/8" of bolt throw and requires force to close lugs into the stops.

Dykem on neck and shoulder shows no contact.

Bolt face shows significant brass transfer.

Will be mic'ing everything tonight when i get back from work, but google-fu has uncovered numerous threads about Forster dies inadequately sizing for minimum spec chambers.

is it possible that the die doesn't adequately size case head/web area with my (redding) shell holder ?

i'm a competent, but unsophisticated reloader and could use some guidance on troubleshooting.

thanks

LaRue Spotr double sided Pic rail

Used but solid

Invaluable pieces of observation kit

2 available

Sold shipped

Leofoto Ranger LS-324C. Area ball head.


$225 to me shipped to you.

Looking for a short action customs - desert tech 223 conversion kit.

Let me know what you have

Thanks

Not an AR guy… snagged sopmod clone upper DD upper with the smaller diameter port I think, threw it on a JP lower, rise trigger, vltor carbine length buffer (A5 I think?) whatever…only cause folks always ask for details.

It’s 10.5” with an RC2 in 5.56 in it…rifle is an absolute scatter gun ever at 50 yards off a bipod. Given, it’s just got a 3x magnifier and a exps on it, but shouldn’t it be a bit tighter than that? Talking 2” at 50 yards with about anything I can find to feed it.

I’m probably going to pull the barrel, but what are some obvious things to check for? Proper torque, nothing loose or touching the handguard, brake/mount is tight…anything else? Not sure how to trouble shoot an AR

Optic is fine, same results after I pulled the eotech and threw it on a riser as well, but everything is shrugged up.

Don’t need it to drive tacks, it’s a truck gun mainly, but anytime I let someone shoot it, they say the same, a DD should be more accurate than that. I shot a 10.5” colt in a class about a decade ago and we were on steel at 400…no way I could do that with this rifle. No Rise trigger in the photo…JP trigger there, but no change for the better when swapped.

Any suggestions appreciated.

My buddy and I are signed up to run the lite division at TTG Sniper Challenge in October. I know it’ll be here before I even realize it. Anyone have any tips for this event? He’s running his 700 AAC SD 308 and I’ll be running my 20” AR10 308 or my 16” recce (planning the AR10, but Murphy’s Law is always in effect). The recce has some good glass (PLXC) and can print moa or less with 77gr stuff. Currently planning the Federal GMM 175smk for the 308 as it’s done the best groups so far out to 200 yards, but I haven’t had the chance to stretch it out past that yet since I finished putting it together last year. I also still need a bipod and a bag for it.

Area 419 Hellfire Match 6mm brake. Brake only, no universal adapter.

$150 shipped

Looking to sell a KRG Xray with the alpha aluminum forend upgrade and heavy rear bag rider. No mag included.

$600 shipped

I have one pair of the Vector X 12x42 w/MSR-DMR reticle for sale
$2899 Shipped CONUS

Up for sale, Bore Guide for Vudoo v1. I've tested it and it does not work in v2 vudoo actions, hence just be sure you have the correct action before purchasing.

Price: 50 USD, shipped to your door.

Acceptable Payment method: PPFF, Venmo, CashApp, all of them discreet (absolutely no comments), or add the 4% fee on top of the listing price.

Items ship next business day.

I have several of these Tangoinnos Fire 4000 Ballistic Rangefinders for sale in black only.
$1400 Shipped CONUS

https://tangoinnos.com/fire4000





https://tangoinnos.com/fire4000

Brand new never opened Gen2
If you haven’t played with these they are amazing. Perfect for you NRL hunters. Lifetime no hassle warranty from Sig.

$2200 shipped
Insurance is on the buyer

Hey there!

I've got a cabelas covenant 7 currently living on my 308 and I'm thinking about possibly upgrading to an Arken EP-5....


HOWEVER, the more I read about the Arken, the more I second guess this move.


Has anyone on here compared the two? I don't really have any complaint with the Cabela's scope, especially being that I got it for a steal (I work PT behind the fun counter).


Anyone care to chime in on this? I could always wait and get something like a vortex pst or a razor next year - just dont want this to be a waste.


Thanks!
-Chomps

I am curious if MPA will ever make a Matrix Pro 2 for the Tikka action? I know they have the Matrix Pro 1 series for the Tikka, however, I cannot find them for sale on your Euro optics nor a lot of places. I see that they still have the regular matrix chassis for sale.

Should I just wait or search for a pro 1? I am in immediate rush or even trying to compete. I am a newbie that is just trying to have a nice chassis to learn on.

In before being called a commie fag.
No it doesn't mean we should have elected Camel-Toe or that sleepy joe is not a pedo sniffing goon.

Triggertech diamond curved this one has less than 2000 rounds in it warranty sticker in place sold shipped

I have an AI AW IMUNS.

I want an AI AT IMUNS.

Straight trade.

Not for sale.

Looking for a SG pulse unit, preferably mlok/Pic model, let me know if you have one to sell.