Accuracy International AT-X

Roger that. I gave it a good internal wipe down with a paper towel jammed in there.
Also federal is soft brass. Hornady isn’t a ton better. So factory ammo loaded hot or close to the lands could have some effect.

Also remember you’re part of the #12lbsboltliftgang with that ATX. So maybe the hornady is just fine 🤪
 
This rifle loves Hornady ammo for some reason. Berger factory ammo is OK, everything is sub minute, but this particular Bartlein LOVES ELD-M’s.

The Federal stuff shot reasonably well for hunting ammo just seems like it might be loaded on the spicy side. Which probably means it should be running large rifle primers. That said I torched of 3 rounds of 129gr Hornady SST “Superformance” and it shot better than the fancy pants Federal stuff, and showed no signs of pressure or primer issues.

I guess I should be happy it likes the cheapest readily available component match bullets and loaded match ammo out there. Like a pretty girl that would rather drink Coors Banquet than Champagne.
 
@RUN8 did the boltface or firing pin get etched? Was there evidence on any of the spent cases of leakage around the primer, or piercing? If factory ammo were etching AI parts, I'd be very vocal with the ammo manufacturer.

If the Federal ammo is leaking or setting the primer back it is worth calling them in the event there is a bad lot out there. Hopefully you still have the offending box with the lot number.

I don't see any recall info on the Federal website. That might just be my web surfing skills.
 
Still have the box and the remaining 16 rounds, I had fired a single round of it back in November at a steel target using the same elevation as some Berger 144gr and it hit to the same POI as the Berger at 523 yards oddly enough.

I see no evidence of bolt face or firing pin etching, just a bit of carbon on the firing pin tip and I noticed a bit of smoke at the rear of the bolt where the firing pin tail protrudes from the bolt shroud. Otherwise I wouldn't have paid much attention to it.

I did leave Federal a report with pertinent details. The lot number of my box is B046U18 in case anyone else has any on hand to be on the lookout for.
 
Last edited:
  • Like
Reactions: anon
I’ve not tested this…

Rumor is cold weather causing ignition issues with srp in larger cartridges
I'm only in to ask if people have had problems with factory 6.5x47 Lapua. I don't think it has ever been sold as anything but small rifle primer.

I have both large and small rifle primer brass for my 6.5 CM and 6XC, never have bought any srp 308 brass. But, that's more of a hedge against primer availability than anything else. I don't load high enough to need srp.
 
Slung some paint!
 

Attachments

  • IMG_1852.jpeg
    IMG_1852.jpeg
    257.8 KB · Views: 167
I'm only in to ask if people have had problems with factory 6.5x47 Lapua. I don't think it has ever been sold as anything but small rifle primer.

I have both large and small rifle primer brass for my 6.5 CM and 6XC, never have bought any srp 308 brass. But, that's more of a hedge against primer availability than anything else. I don't load high enough to need srp.

I haven’t read about any primer issues with 6.5X47 Lapua.

From what I hear it is the proverbial “easy button” of 6.5mm cartridges to load for and achieve single digit SD’s.

It’s a well designed cartridge with the huge advantage of only being available in top quality brass, and that is going to help a lot.
 
  • Like
Reactions: taliv
Says the dude that was wanting to sell an LWTS-LR for $10k when it wasn’t even worth over $8k.

Why’d you delete that thread? My half eaten bag of lays wasn’t good enough for ya?

@Huskydriver
I traded it for a Utc-x.

So

F365ED86-1256-486E-BFB9-D1911C088763.gif


We all have our own opinions of price.

But comparing a Lwts lr that msrp for $25000 and was fire saled by dealers for no less than $14000. And I listed for $10000

Is slightly different than listed a $5250 msrp rifle that fire saled for what $4250. For $4250. Minus the $120 mag and $6-900 barrel but adding a $250 hinge.



Yeah totally comparable
 
I traded it for a Utc-x.

So

View attachment 8347296

We all have our own opinions of price.

But comparing a Lwts lr that msrp for $25000 and was fire saled by dealers for no less than $14000. And I listed for $10000

Is slightly different than listed a $5250 msrp rifle that fire saled for what $4250. For $4250. Minus the $120 mag and $6-900 barrel but adding a $250 hinge.



Yeah totally comparable


So I’m the angry one cause I’m clapping back? 😂

Find me the fire sale… I’ll wait.
Dudes were dumping AT-X for dirt cheap cause of EO’s and MH’s prices. Now they’re gone.

Everyone is crying about that $6.5k pricing on AT-XC.
But I’m smoking crack for my listing? You’re comical


There’s another AT-X with all the bells and whistles for $6k if it’ll make you feel better.
 
  • Like
Reactions: hafejd30
Has anybody ever had issues with Federal 6.5 Creedmoor ammo in their AI or other rifles? Hit the range yesterday and fired 3 rounds of 130gr Terminal Ascent, which is loaded in small rifle primer brass, all the primers looked like shit and one of them backed out a smidge. When I got home and cleaned the rifle I discovered a bit of carbon on the firing pin, so I guess the one that backed out must have released some gas.

Everything else functioned just fine, although a few of the Hornady 140gr ELD-M seemed like they might have had slightly harder bolt lift than the others. No issues at all with any primers in the large rifle primer brass.

This particular barrel continues to display an affinity for Hornady ELD-M’s.

View attachment 8343618
I am not sure which AI you are using but this happens to me all of the time in the AXMC which has a LFP. I don't use terminal ascent but use the FGMM with the Berger 130-grain bullet. Primers are badly cratered. Sometimes they are even damaged to the point where fragments end up preventing the firing pin from working. I have to take the firing pin out and dump the fragments out of the bolt body. It also coats the spring with all sorts of gunk that requires a thorough scrubbing to remove the residue. Norma 6.5 with large rifle primers is even worse than the Federal. I want to try the Berger-loaded ammo since it uses an LRP to see if that works without issue.

I have stopped using Federal and Norma in the AXMC. Like you, I am thankful that the AXMC does not exhibit this issue with Hornady and like you the groups are great so I just use that. My AT which has an SFP does not have these issues so I run the Federal in that.
 
  • Like
Reactions: BurtG
I haven’t read about any primer issues with 6.5X47 Lapua.

From what I hear it is the proverbial “easy button” of 6.5mm cartridges to load for and achieve single digit SD’s.

It’s a well designed cartridge with the huge advantage of only being available in top quality brass, and that is going to help a lot.
I shoot it, and it works great out of the AT-X. Super easy. Feeds great and low recoil for a 6.5
 
  • Like
Reactions: diggler1833
Europtic has border-patrol length AICS, or was I hallucinating LOL
for those of you with any interest in short barrels, any interest?

Cool to see them finally in the field if thats legit.
Tikka stuff...better late than never I guess.
 
Europtic has border-patrol length AICS, or was I hallucinating LOL
for those of you with any interest in short barrels, any interest?

Cool to see them finally in the field if thats legit.
Tikka stuff...better late than never I guess.

The only "Border Patrol" spec is the actual rifle itself with the short forend. The short forend AICS chassis has been out for quite some time now. It was designed mainly for rimfire rifles with shorter barrels.

But, LE prefers shorter forend for short barrels with suppressors. We've been using the short AICS for several department builds.
 
Last edited:
  • Like
Reactions: BurtG
Nice - I stripped one of the screws trying to take the low action rail off trying to put the high rail on....what kind of apes put those on?
I think the screw heads are soft and loose. I bet it didn't even take much force to strip. On advise of this thread I didn't even bother with the hex heads and tapped a T15 bit into the hex head and then they backed out without any issue.
 
  • Like
Reactions: goatboy and bnaples