-
Having trouble using the site?
Contact support
Accuracy International AT-X
- Thread starter Peter Laurvick
- Start date
And for a quick change barrel system like my LMT, mlok makes absolutely zero sense, because you have to remove all the mlok attachments to get the barrel out. If you've got weights all the way down the rail like hic28s pic above, total pain in the ass.
Don't know if mlok on the atx would have the same problem or not.
Hence the above comment about making the rail slightly wider to accommodate said interference.
Tried searching and could not find info. thought I read in this thread what the scope rail screw specs are. Looking to get replacement ones and hoping I didn’t have to read 78 pages in this thread to find the info.
1 page back........if you're removing the factory rail, heat the screw with a butane torch, soldering iron, something. The alloy is soft and the thread lock from AI is abundant!
One page back had the torque specs. I was looking for what thread and length they are. I might of missed it on 1 page back but it is getting late after all.
Took it to the range to sight in, moved the Nightforce optic over from my Sig Cross, only required 0.2mil on the elevation and 0.1mil on the windage to have it zeroed at 100yds. Absolutely love it, did five quick groups and with my shitty shooting I got 0.46MOA on factory Hornady 140gr match ammo, I’m confident next time out I’ll tighten it up to 0.30MOA.
Euro Optic has been fantastic in terms of hooking me up with anything and everything I asked for. Ecstatic that they were able to get one of these in my hands so quick.
Euro Optic has been fantastic in terms of hooking me up with anything and everything I asked for. Ecstatic that they were able to get one of these in my hands so quick.
Probably the face she made when she shit the bed.
this doesnt answer your question directly, and obvious difference between pan and cap head, but these are the screws that came with my high rail kit. i was going to call them monday with a couple wuestions on these and also the original screws with the low rail.
will report back anything i learn
Attachments
Last edited:
Accuracy International AT-X 20 MOA Action Rail Module Kit 29390BL
Accuracy International AT-X 20 MOA Action Rail Module Kit 29390BL For Sale
This is the correct high action rail for the AT-X.
so whats this part? just got it in from EOAccuracy International AT-X 20 MOA Action Rail Module Kit 29390BL
Accuracy International AT-X 20 MOA Action Rail Module Kit 29390BL For Salewww.eurooptic.com
This is the correct high action rail for the AT-X.
i believe, but may be mistaken that '90' is the high AT rail. '94' is ATX specific. they are both very close in height, but '94' is coplanar with front rail. '90' will still work is what i understand.
Attachments
Last edited:
I called Mile High they took care of me. For $200 I’ll tell you what thread and length they are.
You can also use the AT High action rail and AT NVG 20 MOA rail for a coplanar setup on the AT-X
I bet you're missing the correct screws and recoil lugs with that rail you received.
The AT version is 26612.
did you work with mile high or AI direct when you figured that out?
I know that mine didnt come with the locating pins, but it was nothing to pop the old ones out. though i have a question on the circular one as its not as tall as you would think youd want it for the tall rail
I recieved mine from Eurooptic. Reused the pins as well. Ended up figuring it out myself , you will need to buy a different length on the screws
Pretty sure it won’t fit. You want the 4002 at 1.5 inches.
Here is a Minox in 4002. I tried 1.35 rings and they worked but were too short for me to get comfortable behind.
Spuhr is on backwards
Idk I’m running a 4-20x50 in a 1.5 mount with the low rail.
Also your gonna want a 34mm mount lol. Not 30mm
Pic with full rail
Also your gonna want a 34mm mount lol. Not 30mm
Pic with full rail
I’m running the 7-35 in a SP-4901. 20 MOA factory base and 30 MOA 1.18” mount with no issues. The plastic ring on the front scope cap lightly hits the bridge but no issues.
Attachments
147gr Hornady ELDm - FV wind ~7mph last weekend
1" group at 300yd only 3 shot group cuz I was just trying to collect DOPE on a new rifle (holding no windage obviously - practice not a test)
ATX - 6.5CM
Rifle is assembled, ebay bag rider, zco420 in 20moa 1.5" block mount. Ats tuner and ultra7. Weighs 20# all up as you see it. I usually run a modified jaw weld with the butt stock as centered to my inside pec clavicle junction as possible. With the ai cheek set lowest as possible, I still have to run cheek weld to get scope centered to my eye. Perhaps a swap to the AT high rail would fix? Or an even taller mount? Headed to the range here this afternoon to start barrel break in.
I purchased some red mountain arsenal ammo as it was advertised to be in lapua brass, but came in peterson lrp. Not a big deal, was loaded with 136 scenars. If they hung in the 2680-2710 fps range they shot really well. I shot a Kraft drill, 12 shots 12 positions standing, kneeling, seated, prone. I was happy with the accuracy. My 6bra match rig, usually can get it under an inch. Wind was blowing 12-18 mph at 4 o'clock, caused me to throw on the standing shots, as i mistimed my wobble. Shot well under an inch when group shooting. A few cherry picked groups we under 1/3 moa for 5 shots, but average was closer to 0.6 moa. Not bad for 35$ a box.
I purchased some red mountain arsenal ammo as it was advertised to be in lapua brass, but came in peterson lrp. Not a big deal, was loaded with 136 scenars. If they hung in the 2680-2710 fps range they shot really well. I shot a Kraft drill, 12 shots 12 positions standing, kneeling, seated, prone. I was happy with the accuracy. My 6bra match rig, usually can get it under an inch. Wind was blowing 12-18 mph at 4 o'clock, caused me to throw on the standing shots, as i mistimed my wobble. Shot well under an inch when group shooting. A few cherry picked groups we under 1/3 moa for 5 shots, but average was closer to 0.6 moa. Not bad for 35$ a box.
Last edited:
I would maybe ask the company for an official view if/when there is a process in place to eval/cert the .mil ammo. My guess is its very early days and without a formal process may not be commerically public information yet.
Been 17month wait now….. good living in Australia. Getting stupid now. WTF
I jumped ship to an AX and ordered an AO chassis in the end.
The only similarity is they both look like dick and balls running all down the sides of your chassis.
Yeah but they took it next level with the atx, because now they are erect little dicks all over your rail.
Hi, I‘ve also an UK rifle, the light spring was included in the bag with the trigger manual and the Allen keys.
Nice
, Can get the AO out here ay? Finally have hit the shores now 2-3 weeks in customs, so the wait hopefully nearly over 
So we should be putting in our PTA's???? Or wait 'til they get to our LGS??.............................Nice
Thinking I'm gonna wait.
Danny said put it in mate. He’s very confident only 2-3 weeks. They are here now in Australia. I have one that runs out 28 July
. They are quick atm anyway…..week or two!
