Step 1: buy an axmc
Step 2: buy a thumbhole folder at
Step 3: buy an ao/vision chassis for the at
Step4: debond the axmc butt stock
Step5: debond the thumbhole from the at
Step6: install thumbhole folder on axmc
-
Having trouble using the site?
Contact support
Step 2: buy a thumbhole folder at
Step 3: buy an ao/vision chassis for the at
Step4: debond the axmc butt stock
Step5: debond the thumbhole from the at
Step6: install thumbhole folder on axmc
Orrrr…
Step 1a: Buy AXMC-LE
Step 2a: Buy @J-Ham ‘s AT folding stock
Step 3a: Debond the AXMC-LE buttstock
Step 4a: Install the AT folder with thumbhole skins.
Step 5a: Beat @Huskydriver at having the coolest AI.
Step 6a: Win
It Balances a 20” 308 in the old school AI contour just fine and the new heavier AI contour in 24” even better. May be a little far forward if you’re running a truck axle.
Attachments
Ooooh, showin me how to win huh
thank you sm, i looove the thumbholes but sadly they are nonexistent on the market
Ooooh, showin me how to win huh
Could someone share a rundown on the differences between the pre and post 2014 AICS AX chassis? I’m about to purchase one for my Zeus and want to make sure I’m getting the 2 screw forend version (post 2014?).
Wait, AIs need lubed and cleaned??
What tripod sling/cover is that?
Full length rail is on the way. Hoptics 2rnd holder and pad are here. Won’t be able to get home till mlk weekend tho
SORD / LVG - Tripod Leg Covers
SOLD AS A SET OF THREE Designed for a leg diameter of approximately 37mm. Two lengths: 295mm & 440mm. These covers should accommodate approx 34mm - 40mm legs. Protect the carbon fiber legs on your tripod with these highly practical and adjustable leg wraps. LVG assisted in the design of these...
www.lowvisgear.com
96C’s products, exceptional quality gear made in Australia.
Last edited:
Take out the bolt and clean it off with dirt, cut your finger and apply blood liberally. Orphan blood works better but they are harder to find at the range.
Quality is an understatement, they are unreal. Even his hats are bloody durable, I have about 4 of them.SORD / LVG - Tripod Leg Covers
SOLD AS A SET OF THREE Designed for a leg diameter of approximately 37mm. Two lengths: 295mm & 440mm. These covers should accommodate approx 34mm - 40mm legs. Protect the carbon fiber legs on your tripod with these highly practical and adjustable leg wraps. LVG assisted in the design of these...
L96’s products, exceptional quality gear made in Australia.
AICS AX Chassis
PRE 2014:
8 or 10 small screws hold the fore end rail to the receiver part of the chassis.
Rounder, plastic skinned rear stock section, same as the current AT rifle.
POST 2014:
Newer, throw lever style rear end, same as the AX / AXMC.
2 bolts holding the fore end rail to the rear half of the chassis
Can use the Victor Company Hammer fore end rail with inbuilt Arca.
Just read my tag line bro….
From what I remember and I do have one on a AW…is just caliber was engraved twice 180 degrees apart. I could be wrong if it changed at all but that’s what I say.
Later, Frank
Bartlein Barrels
Does Sporting Services send you a tracking number? They billed me for my Thumbhole Skins on 12/24 and the order says "Fulfilled", but that's the last information i got. Anyone provide input?
-Thanks
-Thanks
Yes they do. I have ordered a couple of items from them and they send it through the Royal Mail.
Yes sir. MSR2 reticle. I have been shooting it a few times now and it’s been tracking well. Shot with NV last night as well and it did good.
The 318 is surprisingly good for sub 2k imo
Hey guys, does anyone know what the heaviest contour barrel you can get away with on an AXSR? Will it accommodate 1.350” straight or are you going to have to taper it at some point to 1.200” or so?
I know it’s been mentioned here before, but I can’t find it for the life of me. Must have looked through 150 pages already to no avail.
I know it’s been mentioned here before, but I can’t find it for the life of me. Must have looked through 150 pages already to no avail.
The 1.35" slides down the tube for installation. So I don't see why it wouldn't work. There isn't a whole lot of clearance around the shoulder though.
You can run 1.35 straight in the older MC handguard. The AXSR and MCLE have the new handguard which has small ridges inside and can’t run a 1.35 straight. I forget the exact number but I turned mine down a bit, I think it was like 1.28 or something
Inside the axsr. Those must be the ribs you are talking about. I just pulled the 6.5cm barrel so had the chassis handy. I had no idea they would limit the oal length since the shoulder has to slide down the handguard. Chalking it up to leaning something new.
Yep, those are the ridges. When I sold my MC and got the LE, I dropped the barrel in and thought it was good. Couldn’t hit a full ipsc at 1 k for anything. Went back to 100 and shot a group and it was trash. The barrel when fired, just touched enough to fuckup accuracy. Turned the barrel down a bit and it went back to amazing precision
Like @hic28 said.
I would taper it like a Heavy Varmint.
Have it at 1.350” at the shank for about 5” then start tapering it to 1.250” at the muzzle.
Barrel will still weigh over 10lbs
That’s perfect, I prefer them a little thicc.Like @hic28 said.
I would taper it like a Heavy Varmint.
Have it at 1.350” at the shank for about 5” then start tapering it to 1.250” at the muzzle.
Barrel will still weigh over 10lbs
First day out for the new year. My AXSA Elite Sand with the 308 barrel. Some hard drive disposal @ 200 yards...
ES still the best, even with @Krob95 going to the other side!
ES still the best, even with @Krob95 going to the other side!
All put together. Including the Ultra 7 in 6.5, absolutely love that can.
Anyone know where I can get longer screws for the butt-spacers? It came with extra spacers but not with screws long enough to make use of them. I got long-ass arms and need one or two more spacers.
I gotta get better at talking pictures, my photo skills are not cutting it for this thread
.
View attachment 8041367View attachment 8041368
All put together. Including the Ultra 7 in 6.5, absolutely love that can.
Anyone know where I can get longer screws for the butt-spacers? It came with extra spacers but not with screws long enough to make use of them. I got long-ass arms and need one or two more spacers.
I gotta get better at talking pictures, my photo skills are not cutting it for this thread
Ace hardware
Similar threads
