-
Having trouble using the site?
Contact support
Ingenuity Precision trickler
- Thread starter NiteQwill
- Start date
Now to figure out how to cut that needed hole in the Area 419 top plexiglass .... Any Ideas? Just drill it? I think a special bit is needed for Plexi / Lexan.
Stepper bit. Go slow and take breaks to avoid melting it.
I finally got mine set up but haven't run it. Gonna have to get a new straw but I got it taped up for now
I am very happy with the IP. I finally got to use it and once you get the speed dialed in with the slider on the back of the scale, it really does work great .
I load 42.65gr for 6.5cm with starline brass and a Berger 130 otm. I set it up to drop about 40.5 gr and trickle the rest. Once I got the speed dialed in (5 min max), it would drop 42.64gr on the nose every time. I only loaded 15 rounds because I didn't have much time and was just dying to test it out. It's very fast too. I have a pre order for the V4 and I've already traded my spot once but at this point I will probably just stick with the IP set up as I have it now and let someone else have my v4 spot. If I didn't already have the v3 set up I may give the v4 a whirl but the IP is very easy to clean up when done and if it continues to work as it has so far, I will be absolutely ecstatic.
I have the ball powder disk coming. I wish it was available on the site when I completed the IP order so I didn't have to pay the shipping again the day after but I'm glad to have it coming. I will give some reporting on it when I get it and use it. Paul says it works extremely well.
I should also mention that I emailed Paul about the disk and a possible issue with my IP straw caused from it falling onto a tile floor and Paul called me immediately after I sent the email to tell me how to fix the straw and then put my disk order in and sent me a link. I thought that was pretty cool! He's a really nice guy with a great product and obviously it speaks extremely well for future CS.
A lot to like about Ingenuity Precision!
Run your V2 with an IP. You will be happy.
Order 25045, delivered 9/15. Just got it set up today. Going to load some Wednesday
I actually talked briefly to him about that... He indeed sold A LOT of units, to say the least.
How ironic... my email just came now so im all paid up and its shipping out.
Congrats. Just got my ball powder disk and will see how that goes this weekend.
Looks like they are getting them put the door pretty quickly and catching up!
I'm #24810
The order numbers are all goofed up so you never know when your order is gonna pop up. I ordered in June and my order number is 247xx.. So in my case it's better to just forget about it and wait for the surprise email, which I will never do. Lol
I've probably loaded now close to 500 rounds to finish off the season. It's been such a pleasure having consistent, on the mark powder drops.
Glad everyone is (slowly) finally getting their emails.
Glad everyone is (slowly) finally getting their emails.
I'm 24810 and ordered July 6th....so order number makes sense if you ordered June 247xx
Either way...hoping for an email shortly
Mine showed up a week ago, still in the box lol. Haven't yet drilled a hole in my top plate of the scale. Will try get at it soon!
I have mine - it’s cool but not really great for me until I get other disks for the large grain powders, so I’ve got the v4 set up plus the IP , if I’m using varget or the likes , I use the IP , 20N29/rl50 use the standard v4 plus a dandy trickler for that 1 grain issue , I communicated with Paul same response, he is waiting on the manufacturer, when he gets them in he will post them on his website. I hate waiting…. Just for clarity I got a spare motor from Adam - so they are good to go
Just got mine setup tonight, super easy. I’m dropping charges in 8 seconds with no issues. Ready to buy a second one.
My preorder number was 24616 and delivered this past Saturday. When you get the email and you pay for the final order, the system generates a new final order number. My trickler was delivered under order number 25246. I think that’s where the confusion comes in.I was going by this @padom , Maybe just an anomaly or something who knows, im just anxiously awaiting that email.
Sounds like Paul is catching up on the basics , hope he can do the same with the disks
Got mine last week, I can throw 10 charges in under 2 minutes. I also got all the plates as well with my order some how? I don't know but I'm not complaining lol
Please do , likely you got 3 , the same 3 every one else got , none of which work with ball powder or large grain powder like rl50
