Same. I was able to find one on Amazon and have posted the link in the T3 thread before.
-
Having trouble using the site?
Contact support
Tikka T1X
- Thread starter jbell
- Start date
Do you have enough forend material to install a t-nut? I honestly have sold off all my factory stocks as soon as I bought a new tikka. You could buy an area 419 pic rail and they come with multiple t nut hardware. You need 2 anchor points to mount a pic rail or it would spin on you.
Took the T1x (in a Manners Prs1tk w/ mini chassis) and practiced transitioning prone, kneeling, standing. This thing is a nail driver.
I mounted a scope and sighted it in when I first got it. It shot well in stock form. The bravo showed up a few days later and I upgrade the scope to the Tac shortly after that. This was my first time shooting groups with the whole package. Its a no brainer for you to get a Bravo for yours. Matched set for the win.
Thanks is a KKC stock made by Altamont stocks. Quite comfortable. It’s the poor mans GRS stock
Had a short period to shoot today, so I took the kids out with me and only got to shoot about 30 rounds through the tikka (about 10 shot of bulk ammo to get it dialed in and then 4- 5 shot groups with Eley action)
View attachment 7338537
all but one group could be covered with a dime (51 yards). Not bad for a portable table and a light breeze. The gun is definitely more accurate than I am. Super excited to see if the wife will compete in the nrl22 with it this year.
Damn. Wished I had kept it now. Ha ha ha
Was able to make it out and put my T1x in 22LR on the BOG tripod and run it out to just under 400y which was a lot of fun. Even got the T1x in 17hmr out on steel which was far easier. Surprisingly never shot groups with either, just zeroed them on golf balls or empty beer cans. Both are great rat and rockchuck rifles. Built the 17hmr so good buddy could have something to shoot, so I don't have to listen to his 22-250 ringing my ears. Was able to anchor five rock chucks yesterday with the 22 though.
The .22 is really liking the Remington ELEY EPS Match and the 17 performs well with the Hornady XTP 20gr HP's. Wanted to try the CCI A17, but wasn't able to find any locally.
The .22 is really liking the Remington ELEY EPS Match and the 17 performs well with the Hornady XTP 20gr HP's. Wanted to try the CCI A17, but wasn't able to find any locally.
Stock on the bottom is a B&C Sporter, but for the money I am not very impressed. Considerable amount of flex in the forend and required signaficant sanding to be able to free float. Any weight on the front end with a bipod and it is touching immediately. I might just toss back on the factory stock and give it a Krylon marble spray in OD instead. Honestly more impressed with the factory stock setup than the B&C sporter.
Obviously left on the vine after being marked at 16.5 and continued to grown to its present length.....
If it was a coin it would be valuable as a mis-mark.
If it was a coin it would be valuable as a mis-mark.
16.5" is the twist rate of the barrel not the length. Its marked the same on mine.
Interesting, mine has completely different looking markings. Much deeper stampings on mine - and there is no serial number on the barrel.
Are you in the US or other markets?
Are you in the US or other markets?
That makes sense! I’m surprised the twist rate is so slow. It’s also written differently than I’ve seen on other rifles. I guess I would have expected it to be written 1:16.5.
Messer, I am in the US market.
Messer, I am in the US market.
Perhaps the markings change is an indication of a batch change with Tikka. New markings were likely not part of the first production run. I wonder if any other changes were made.
I'll take some pics later and post them.
I know mine was ordered from the distributor back in the beginning of April. They had it in stock, but shipping took a little more than two weeks.
I know mine was ordered from the distributor back in the beginning of April. They had it in stock, but shipping took a little more than two weeks.
I just checked mine, and the markings are completely different. Purchased in the US last July
Attachments
From New Caledonia
T1x, IBI bull barrel 20", Hardy suppresor NZ, Area 419 30 MOA rail, ERATAC 20 MOA unimount, Athlon scope, MPA chassis T3X.
T1x, IBI bull barrel 20", Hardy suppresor NZ, Area 419 30 MOA rail, ERATAC 20 MOA unimount, Athlon scope, MPA chassis T3X.
Mine loves SK Rifle Match and CenterX. I heard that alot of people are getting good results from CCISV. I just bought a few boxes to test out, since its a good amount cheaper than buying bulk SK or Lapua.
had a great time sighting it in. This was my best group at 50 yards shooting CCI Standard Velocity. Also had surprisingly good results with Federal Bulk pack, which is a win.
With a couple little changes (I need a proper rear bag and I’d like to lighten the trigger a hair) I bet the groups could get even better.
Edit: I did discover that Remington Golden Bullets were horrible out of my rifle. Maybe 1.5 inches at 50. I’ve never been a huge fan of Remington .22 anyways.
With a couple little changes (I need a proper rear bag and I’d like to lighten the trigger a hair) I bet the groups could get even better.
Edit: I did discover that Remington Golden Bullets were horrible out of my rifle. Maybe 1.5 inches at 50. I’ve never been a huge fan of Remington .22 anyways.
SK for me. The brick of CCI SV I was shooting was giving me pretty consistent feeding and ejection issues.
I have another question, I noticed accuracy falling off during today’s range session (probably my fault) but it made me wonder, how often does everyone clean their T1X? What’s your cleaning technique?
I’ve got around 300 rounds through the rifle and haven’t cleaned it yet, mix of copper and lead loads.
I’ve got around 300 rounds through the rifle and haven’t cleaned it yet, mix of copper and lead loads.
So shot about 50 rds of CCI SV. Compared to SK and CenterX, the groups were damn impressive for 1/3 the cost. I think it is great ammo to practice. At $3.99/50rd its a no brainer.
I have a case of CCI SV and a brick of Tac22. I put on the Magneto-speed today and 10 rounds of the CCI SV measured an average of 1072fps with an ES of 32. The 10 rounds of Tac22 averaged 1039fps and an ES of 20.
I'm guessing the better (expensive) ammo has better extreme spread as shown by the Tac22. Not sure if it matters much at 50 yards but a high ES can't help. I did shoot a USBR target with the CCI SV today and got a 214 and that's pretty good for me.
I'm guessing the better (expensive) ammo has better extreme spread as shown by the Tac22. Not sure if it matters much at 50 yards but a high ES can't help. I did shoot a USBR target with the CCI SV today and got a 214 and that's pretty good for me.
Another vote for CenterX. That has been my most consistent best performing ammo.Time for some ammo testing. What is your money one?...
Center x is my guess. It runs the most consistent in my rifle after the Remington Eley club xtra which isnt made anymore
what aftermarket trigger are you guys using?
My wifes trigger won't reset all the time and I have made the trigger as heavy as possible to fix that issue but if the gun is pointing up or you cycle it too fast the trigger wont reset. I can fix this by pushing the trigger forward and cycling the trigger. It's like the trigger return spring is too weak.
My wifes trigger won't reset all the time and I have made the trigger as heavy as possible to fix that issue but if the gun is pointing up or you cycle it too fast the trigger wont reset. I can fix this by pushing the trigger forward and cycling the trigger. It's like the trigger return spring is too weak.
Wolf Match Extra and center x for meTime for some ammo testing. What is your money one?...
Same. If you’re just practicing tripod shooting or steels or barricades - save the $ and use CCI SV.
Nearly finished setting this up. Just waiting on a Sterk swept knob.
Tikka T1x 22LR with 20" barrel
Oryx Chassis with two additional spacers
Atlas Bipod
WieBad cheek pad
Area 419 30 MOA scope base
Vortex PMR rings
Vortex Strike Eagle 5-25x56
Tikka T1x 22LR with 20" barrel
Oryx Chassis with two additional spacers
Atlas Bipod
WieBad cheek pad
Area 419 30 MOA scope base
Vortex PMR rings
Vortex Strike Eagle 5-25x56
@BrigandActual I really like the blocks you are using to hold the rifle on the peg board. Did you make or buy them?
The board and attachments are all Gallowtech. I have different hooks and mounts all over the place for things.
Went to shoot my first NRL match this weekend. Head over to the sight in range and my first trigger pull, firing pin breaks. Sent a message to Beretta and they dropped a new firing pin to me in the mail. Simple Customer service experience.
That's some tough luck. I guess I should order a spare since they're only 60 bucks and I keep seeing people mention broken firing pins. Too bad you need to buy it as the whole assembly.
Went to the range this morning to zero after all the recent upgrades. I'm very pleased with the results.
T1x in an Oryx chassis
DIP bolt handle
Jamer Benchrest bag rider
Kaw Valley Precision linear comp
Bushnell Forge 3-18x50 on a DIP 25 MOA rail
Ammo: Eley Semi-auto Benchrest Precision
Those groups were shot back-to-back with a small scope adjustment in between. I figured I'd better stop shooting groups before I screwed it up.
I love this gun in the Oryx for positional shooting.
(Pic before the bag rider and comp were installed)
T1x in an Oryx chassis
DIP bolt handle
Jamer Benchrest bag rider
Kaw Valley Precision linear comp
Bushnell Forge 3-18x50 on a DIP 25 MOA rail
Ammo: Eley Semi-auto Benchrest Precision
Those groups were shot back-to-back with a small scope adjustment in between. I figured I'd better stop shooting groups before I screwed it up.
I love this gun in the Oryx for positional shooting.
(Pic before the bag rider and comp were installed)
Hey guys - looking for a 17hmr and not sure if it will be better to get the 16 or 20" version. I will be running a can. Any thoughts on if accuracy will be effected by the shorter barrel?
Accuracy should be fine with either but read this thread for 17 hmr barrel length info
www.snipershide.com
If you go with the 20 you can always get it shortened and threaded again to 18 or 16 or whatever in between. I got the 20" 22lr and with the factory barrel profile it is pretty light in the front even with an aac element on the end(a little over 4 oz and 17hmr rated).
Optimum barrel length on 17 HMR, I am confused
So I have been looking at purchasing a higher end 17 hmr. I was going to build a CZ 17 HMR and started looking at a lot of things. I noticed that the all the higher end guns had 22-24 inch barrels. Anschutz and Sako . So I thought that is what I wanted to do. I looked up the optimum...
www.snipershide.com
If you go with the 20 you can always get it shortened and threaded again to 18 or 16 or whatever in between. I got the 20" 22lr and with the factory barrel profile it is pretty light in the front even with an aac element on the end(a little over 4 oz and 17hmr rated).
