I still can't get vudoo 2 reply to emails so no idea what that feels like
That is strange.
Have you tried calling?
-
Having trouble using the site?
Contact support
Vudoo Gun Works V-22 Rimfire Bolt Action
- Thread starter RAVAGE88
- Start date
That is strange.
Have you tried calling?
I still can't get vudoo 2 reply to emails so no idea what that feels like
What address are you sending to? I'm looking at all the accounts and don't see anything unanswered....
MB
This has not been my experience with Vudoo Gun Works.I still can't get vudoo 2 reply to emails so no idea what that feels like
Have sent two emails and had replies within 48 hours both times....I still can't get vudoo 2 reply to emails so no idea what that feels like
My CZ is getting very lonely all by itself....I think it needs a new big brother to keep it company during the shutdown
Your CZ will continue to be lonely, due to neglect, if you buy a Vudoo!
Speaking from personal experience.
I shot a 6x5 with my CZ 457 last week, and it didn't come close to shooting as consistently as my Vudoo.
I hadn't shot it since acquiring my Vudoo, about 2 months ago.
My Vudoo V-22 w/ 18" Ace Kukri barrel
My neglected CZ 457
Last edited:
Those are both beauties!! Love the Stock on the Vudoo!!Your CZ will continue to be lonely, due to neglect, if you buy a Vudoo!
Speaking from personal experience.
I shot a 6x5 with my CZ 427 last week, and it didn't come close to shooting as consistently as my Vudoo.
I hadn't shot it since acquiring my Vudoo, about 2 months ago.
My Vudoo V-22 w/ 18" Ace Kukri barrel
My neglected CZ 427
I am having trouble loading the 10 round mags all the way. It is not the mag. It is my arthritis. I want to buy a 15 round mag but I am wondering if there is something I can buy that will help me load all 15 rounds. Thanks.
When I load my 10 rounder, the first 5 go in perfectly, once I get to 6-10 the rim side of the round sticks up instead of angling down like the first 5 and makes it harder to load. Not sure if they are all that way or just mine. I'll have to pay more attention to it and see if I can figure out what's going on.
Well worth the three or so minutes to watch. I tried several different ways to load before watching this.
To add. I prefer to load at a table, sitting down. I hold the tabs with my left hand, index and thumb, from the rear of the magazine and straddle it with the web of my hand while the magazine bottom is flat on the table. I have at least ten rounds ready, I try to use multiples of ten to keep counting simple, and just load on at a time following the above procedure. Small increments helps. As stated above, the first five go in easy peasy then the next five takes some practice to get them to just drop in and fall into place. I also have 14 mags now, working on at least 20, so I can do most of my loading at home at the island in my kitchen. Probably gonna stick to mostly poly mags for that reason. 
Looks to be there to retain the action screw when the action is removed. But just a guess...
I happened upon this just now...
Vudoo Speed Loader
Small speed loader for filling the vudoo magazines. makes it a little easier on the thumbs especially when using the extended magazines as the slider needs to be removed. Has a small hole on either…
jklprecision.com
I would like to see a video of how it works. Looking at itI can’t quite wrap my mind around how it works.
Mag extension installation and speed loader demo. After he installs the magazine extension he loads the magazine using the speed loader.
Thanks!
Has anyone had luck with any of the mag extensions? I’ve tried two different brands and had feeding issues with both. I just went back to may standard 10 round magazines which are reliable in stock form.
I just put mine all back to factory configuration. The thumb lever makes loading so much easier. I’m more concerned about reliability anyway. I have an aluminum 15 rd magazine in the way so if I need more than 10 for anything I have that.
My encouragement is usually “embrace the suck” or when one of the more experienced shooters tanks a stage it’s usually “that’s okay, I remember my first match too”. We have one match director that is very fond of using springs on his barricades. Talk about embracing the suck. That’s just cruel.
[email protected] from memory.
One was a month ago asking basic questions which have been answered here.
Last one was 8th May asking about boreguides and were u willing to send non firearm stuff to Australia. Also asked when the aussie order was planning to be sent as I need to submit paperwork to get "permission to aquire" which takes time but also has a limited life span, so it's a bit of a balancing act as if I wait till its at gunshop i could have a 21day wait till I pic it up.
I 100% admit I've heard only good things about your customer service and wasn't to concerned.
Also while I'm here do you guys have large res logo pics that we are able to get printed as a decal for gun case or do you care if we do it. I'm using a cheap hard case and it's got a large "toolpro" printed on the front so may play arround with a decal to cover it. Don't want to infringe copyright stuff though.
Matt,
Thanks for the info, I found your email and it's showing that it was read and forwarded but there's no forward address. I'm thinking a reply was attempted but the FORWARD icon was hit instead of REPLY....Something strange happening and I apologize for the issue, I'll get it figured out.
In the meantime, I've designed a new Bore Guide and we're teaming up with BoreTech to make it. I received a first article mid last week and signed off on it yesterday, so it's going into production within the next few days. The new Bore Guide is compatible with Gen 1, Gen 2 and Gen 3 (three lug) V-22 actions; the legacy guide is only compatible with Gen 1 actions. We'll ship to Australia and the new guide will also be available through BoreTech, along with all their usual cleaning supplies, which we'll maintain an inventory of as well.
Please email me directly at [email protected] and I'll square away the high rez pics and other questions.
Thanks again Matt and sorry for the email issue.
MB
Cheers guys.
Only other thing is do you have a reccomened rod/jag set up ect ect as everything will be order in for me. Plus I've heard some people use the .17 rods. But now that will be all out the window.
Got your email as well once I look into the decal a bit more I'll let you know. I'm hoping to have the gun by end of year so it's not a great rush.
I've been using a smorgasbord of different rods and jags over the years but switching over to the Proof Positive line from BoreTech. The .20 cal rod with .22 cal jag is ideal and I've always used BoreTech cleaning solutions from the time they've been available. We're working with BoreTech to put a complete cleaning kit together (cleaning solution, rod, jag/brush, patches, etc) and will offer it from Vudoo and BoreTech. I've never supported using the caustic solutions and CLR (like you get from the hardware store) is a really bad idea. We get the question about cleaning A LOT, so we're responding with the assembly of a complete kit.
Let me know when you're ready for the logo and I'll get you the preferred file type.
MB
Thanks. $240 later and I have my cleaning rod and supplies coming. Is it too late to cancel my 3 pack of mags I ordered yesterday?
Mike, are you saying the guide on your website will no longer exist? I just ordered one with my rifle. Greg said it would be in by the time the rifle shipped. Or was he talking about the new style bore guide?
I have been using the BoreTech Carbon remover on my rimfire (& centerfire) and feel it is the best solvent I have ever used for rimfire. I am also a big fan of BoreTech products.
Thanks. $240 later and I have my cleaning rod and supplies coming. Is it too late to cancel my 3 pack of mags I ordered yesterday?
No sir, not too late, just call the shop and they'll square it away for you.
MB
Got my Vudoo out for the first time today.
Zeroed at 25 yards. Then out to 50 and 100. At 100 yards ran out of time and spotting tools to
tighten up the groups. Couldn’t spot where I was hitting. Will get back out later this week to get it tightened up. But really thrilled with the smooth feeding and action on this. What a pleasure this rifle is to shoot.
Zeroed at 25 yards. Then out to 50 and 100. At 100 yards ran out of time and spotting tools to
tighten up the groups. Couldn’t spot where I was hitting. Will get back out later this week to get it tightened up. But really thrilled with the smooth feeding and action on this. What a pleasure this rifle is to shoot.
Finally got a case together for ammo /magazines and have 2 kydex magazine pouches shipping from @DedicatedShooter today
. 
. 
. .
I keed.
This three pack gets me to 17 including my 12 rounder. Which I was able to load to 13. It cycled them the first time I tried 13 but had trouble with the first round the 2nd time. Anyone else getting 13 in there? I wasn't even trying. I loaded it up w/o counting and started looking for the missing round to go back in the box. I unloaded it and sure enough, 13.
Now if I can find your bore guide I misplaced and cannot seem to locate.
Hey guys, for anyone who is interested I just dropped Dedicatedshooter a Vudoo magazine in the mail so he can make some Kydex mag carriers for it. He has an ad up down in the PX. I have been looking for one made for the Vudoo mag instead of just the AICS version. SAP has them but I like his a little more based on what I’m seeing. He has some great prices so you may want to take a look if you need one.
Accessories - “The Original” Adjustable Retention Mag and Kestrel Holders
Updated May/June ‘21 “The Original” Adjustable Retention Kydex Mag Holders for Short or Long Action AICS-pattern, V22, B14r, magazines, and Kestrels for sale! Details: - Carbon fiber in either OD, Black, or Coyote - Adjustable retention device - Flared opening - SA holder fits ALL steel...www.snipershide.com
Do you like the design better or is it just the price? I prefer the design and quality of the SAP. You get what you pay for.
SAP Kydex Vudoo Magazine Holster - Short Action Precision
Here's a great way to keep your Vudoo mag handy right on your belt or pack! Custom molded Kydex holster fits your Vudoo magazines perfectly. Molded to protect the .22LR feed lips and loaded rounds. They attach using a High Strength hooked clip to attach to your belt, so you can be confident that...
www.shortactionprecision.com
Right now I am basing my assumption on photos but I do like the design better. The ones I ordered are slightly flared at the top and have a more molded look. The SAP one look like they could be flared a little but it’s hard to tell. The ones I ordered just shipped out so I will see if the concept works as well in use later this week. I honestly don’t really care about the price that much. I will pay more for something if I know I’m getting exactly what I want. I can’t put my finger on what it is but something about the look of the SAP design doesn’t appeal to me. I was in the process of shopping for a different one and was just going to buy a standard AICS holster when the ones in the PX popped up. Ended up being perfect timing.
I am hoping I can pull the trigger on a V-22 barrel action soon. I know the ACE barrel is their barrel, but is there any advantage or disadvantages of it over a Bartlien?
I’m sitting in at least 6k of Eley contact I hope it would like enough for practices. Also luckily my Sister in Law lives in Columbus OH so I can eventually make a Lapua test trip.
I’m sitting in at least 6k of Eley contact I hope it would like enough for practices. Also luckily my Sister in Law lives in Columbus OH so I can eventually make a Lapua test trip.
Last edited:
I went with the Ace barrel myself and it shoots fantastic. I really think no matter which barrel you get it will shoot well.
I tried shooting Eley contact in mine and it shoots fantastic. It is just really difficult to chamber because of the shape of the bullet. If you are just shooting from a bench and not in a match against a clock it will probably not be an issue though. Anything made by Lapua/SK chambers and shoots beautifully though.
I tried shooting Eley contact in mine and it shoots fantastic. It is just really difficult to chamber because of the shape of the bullet. If you are just shooting from a bench and not in a match against a clock it will probably not be an issue though. Anything made by Lapua/SK chambers and shoots beautifully though.
Similar threads
