-
Having trouble using the site?
Contact support
6.5 Grendel
- Thread starter padom
- Start date
I get 2700 with 29.9gr of N133 w/ 90gr TNT from my 12.5” Rainier bbl. 2940ish from 20” barrels.
I run 29.6gr N133 with 90gr Varmageddon and it’s about 40fps slower but extremely low SDs and great groups from two different 20” barrels.
Guys, I'm using the RCBS 2 die set for grendel. When seating a 123 amax, I notice it feels a bit weird and then leaves a ring. What seater dies or seating stems are you guys using for these shape bullets?
It should be noted that I would also want something that works with 107smk as I may be buying some soon.
It should be noted that I would also want something that works with 107smk as I may be buying some soon.
Lol no.
Not all seating stems work with all all bullet types. I process the brass exaxtly the same with SST or match burners as I did with the AMAX and this only happens with the AMAX.
I've asked before and no replies, I'll ask again.
Can somebody help me find out which seating stem I need? I am reloading using RCBS dies. I've tried 120 match burners, 123SST, and 123AMAX. The AMAX does not seem to have a proper fit and the die is leaving a ring on the bullet as well as producing a weird feeling when initially seating the bullet. I think the plastic tip was hitting first, then getting squeezed a bit til the die contacted the bullet and leaving rings.
I'm gonna start loading 107 SMK & TMK and want to be problem-free.
Does anyone know a seating stem replacement or even a seater die I could buy that will have a better fit to these long sleek bullet shapes?
@LRRPF52 maybe you know?
Can somebody help me find out which seating stem I need? I am reloading using RCBS dies. I've tried 120 match burners, 123SST, and 123AMAX. The AMAX does not seem to have a proper fit and the die is leaving a ring on the bullet as well as producing a weird feeling when initially seating the bullet. I think the plastic tip was hitting first, then getting squeezed a bit til the die contacted the bullet and leaving rings.
I'm gonna start loading 107 SMK & TMK and want to be problem-free.
Does anyone know a seating stem replacement or even a seater die I could buy that will have a better fit to these long sleek bullet shapes?
@LRRPF52 maybe you know?
Ultra Micrometer Seater Die. Forster Products. 6.5 Grendel number is U 000 59
www.forsterproducts.com
Hopefully there is "no more" supply shortages due to the KOHvHid scam. I had to wait about 6 months to get mine.
It works great. I am seating 108 Grain Lupua Scenar bullets in Starline brass. Had my VERY BEST luck so far for TAC powder.
3 LOADS… Mar 28, 2024
FACTORY NEMO 120 Gr FMJ BT
H 2596 Low 2515 Avg 2567 Ext Sprd 81 SD 32.8 Not that tight of a group either
TAC by Ramshot powder 27.8 and 27.2 108 Gr Scenar LUpua bullet
27.2 Gr TAC H 2467 L 2336 AVG 2401 Ext SPRD 131 SD 92 cover 4 with a Quarter last one opened up
27.7 Gr TAC H 2452 L 2425 AVG 2438 Ext Sprd 26 SD 13.1 ß all 5 bullets you could cover with a dime!
2.221 overall length. CCI 41 starline brass 2nd firing cut to 1.510 Palmetto armory rifle w/ 1 in 8 twist SS 20 inches long..
Timney Trigger drop in 3 pound pull
The ONLY groups I have been able to achieve with the 120, 123 grain bullets (whether Hornady or Sierra or Gold Dot) has always been with 27.7 grains of Varget, Std Sm Rifle Winchester primer, and either Starline or Hornady brass. About 13/16 of an inch but the speed is SLOW at 2350 approx and that is through a 20 inch barrel
I still have WORK to do. My problem is what is available to buy to load with. Powders, bullets, primers etc. KohVhid has been the biggest scam in my 78 years of life!!
Bench Rest® Ultra Micrometer Seater Die – Forster Products
Order according to the profile of the specific cartridge. U00002,U00004,U00007,U00010,U00013,U00017,U00016,U00019,U00022,U00023,U00200,U00025,U00028,U00031,U002
www.forsterproducts.com
Hopefully there is "no more" supply shortages due to the KOHvHid scam. I had to wait about 6 months to get mine.
It works great. I am seating 108 Grain Lupua Scenar bullets in Starline brass. Had my VERY BEST luck so far for TAC powder.
3 LOADS… Mar 28, 2024
FACTORY NEMO 120 Gr FMJ BT
H 2596 Low 2515 Avg 2567 Ext Sprd 81 SD 32.8 Not that tight of a group either
TAC by Ramshot powder 27.8 and 27.2 108 Gr Scenar LUpua bullet
27.2 Gr TAC H 2467 L 2336 AVG 2401 Ext SPRD 131 SD 92 cover 4 with a Quarter last one opened up
27.7 Gr TAC H 2452 L 2425 AVG 2438 Ext Sprd 26 SD 13.1 ß all 5 bullets you could cover with a dime!
2.221 overall length. CCI 41 starline brass 2nd firing cut to 1.510 Palmetto armory rifle w/ 1 in 8 twist SS 20 inches long..
Timney Trigger drop in 3 pound pull
The ONLY groups I have been able to achieve with the 120, 123 grain bullets (whether Hornady or Sierra or Gold Dot) has always been with 27.7 grains of Varget, Std Sm Rifle Winchester primer, and either Starline or Hornady brass. About 13/16 of an inch but the speed is SLOW at 2350 approx and that is through a 20 inch barrel
I still have WORK to do. My problem is what is available to buy to load with. Powders, bullets, primers etc. KohVhid has been the biggest scam in my 78 years of life!!
I was having the same issue, and I took one of the affected bullets and some valve grinding compound and polished my seating stem. I also started using a mandrel die to open the case necks and have all but completely eliminated the ring impression on the bullets.
I use the Forster Ultra BR (and the standard Forster BR) and have since I started with the Grendel in 2010ish. I polish the ID of the stem and the only time I ever got a ring is when my case necks were sized too small. That issue was related to one particular sizing die that is in a box somewhere.
I use either a Forster FL die or a Wilson FL bushing die with a mandrel die for sizing and anneal.
I sounds to me you have more of a sizing issue or a too clean ID of the case necks. Polishing the ID of the stem will never hurt either.
The "too clean ID of the case necks" might be it. I had never thought about that. As far as sizing, I don't believe that to be the issue but I suppose anything is possible. I run an LE Wilson mandrel that is .263 so it's not like the necks are ridiculously small.
I'll have to check my notes when I'm home. I know I've loaded plenty of virgin starline. If that was the case when I had the rings, it might be the clean necks like you mentioned.
I'm assuming this happens because of friction or not enough lubrication?
Same same on the "friction or not enough lubrication". A stiff nylon brush chucked into a vise milling machine (drill in a vice) will work wonders, be a filthy creature and don't clean your brass, or try the dry lube in the neck like Neolube No.2. All will work more or less. I'm not a filthy creature and clean my brass so that is out for me....
I run a .2615" mandrel in my annealed and sized brass so if you are using a .263" mandrel, a tight ID on the necks is probably not your issue.
I would still polish the ID of your seating stem as it takes very little time and there are no downsides that I can fathom.
I run a .2615" mandrel in my annealed and sized brass so if you are using a .263" mandrel, a tight ID on the necks is probably not your issue.
I would still polish the ID of your seating stem as it takes very little time and there are no downsides that I can fathom.
If you were using Redding dies, easy button would be a VLD seating stem, vs std.
“The Redding Competition Seating Dies for bottleneck cases are supplied with a free-floating seat stem that works well with the most common bullets available for the given caliber. Redding also makes these VLD seat stems for use with many popular VLD style bullets. These bullets have a much shallower ogive angle and may actually bottom out in the standard seat plug. The VLD Seat plugs have a proper internal contact angle and generally a smaller diameter to engage a VLD bullet in a more effective position for proper seating.”
Since you’re using RCBS dies, lapping your stem to the specific bullet, or merely relieving or chamfering some of the sharper internal edges of stem might be pretty easy way to address issue. If bullet tip is contacting stem before ogive, you might want to modify stem ID to eliminate same.
I’ve run into your issue when I have assembled ‘generously compressed’ loads,
which I avoid, though my favorite AR Comp does require a small amount of handle pressure when seating, especially with softer bullets. A short double stroke at bottom of cycle to assure consistent seating depth.
I tumble, anneal every firing cycle, use Redding lube on exterior, Redding Imperial dry neck lube on interior, and have migrated to Forster FL sizing dies and Redding carbide mandrels for case prep, and Redding Comp seating dies. Very low runout, .002 neck tension, excellent SD’s and accuracy. Shoot a lot of 120gr Scenars and no bullet marking.
One more thing-I feel pretty confident with my process, but as a double check on neck tension, even after annealing, I use a Forster neck gauge, and have found in some instances, another pass on mandrel required to assure even neck tension. If you’re not annealing, neck spring back could be yielding more grip than you might expect.
“The Redding Competition Seating Dies for bottleneck cases are supplied with a free-floating seat stem that works well with the most common bullets available for the given caliber. Redding also makes these VLD seat stems for use with many popular VLD style bullets. These bullets have a much shallower ogive angle and may actually bottom out in the standard seat plug. The VLD Seat plugs have a proper internal contact angle and generally a smaller diameter to engage a VLD bullet in a more effective position for proper seating.”
Since you’re using RCBS dies, lapping your stem to the specific bullet, or merely relieving or chamfering some of the sharper internal edges of stem might be pretty easy way to address issue. If bullet tip is contacting stem before ogive, you might want to modify stem ID to eliminate same.
I’ve run into your issue when I have assembled ‘generously compressed’ loads,
which I avoid, though my favorite AR Comp does require a small amount of handle pressure when seating, especially with softer bullets. A short double stroke at bottom of cycle to assure consistent seating depth.
I tumble, anneal every firing cycle, use Redding lube on exterior, Redding Imperial dry neck lube on interior, and have migrated to Forster FL sizing dies and Redding carbide mandrels for case prep, and Redding Comp seating dies. Very low runout, .002 neck tension, excellent SD’s and accuracy. Shoot a lot of 120gr Scenars and no bullet marking.
One more thing-I feel pretty confident with my process, but as a double check on neck tension, even after annealing, I use a Forster neck gauge, and have found in some instances, another pass on mandrel required to assure even neck tension. If you’re not annealing, neck spring back could be yielding more grip than you might expect.
If my memory serves correct, this was new brass so it was annealed at the factory. Or are you implying that if I myself am not also annealing, there will be spring back regardless of it being new brass?
If factory annealed, should be minimal spring back. For future loading, if not annealing, may develop some degree of spring back after several firings. I’m pretty OCD about the details, so anneal every firing and have very consistent neck tension and low SD’s. I use same process loading for either bolt or semiautos.
Similar threads
