.300wm - .300wsm

[ChadTRG42]

Re: Loads for .300WM-.300WSM

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: BAZ_0157</div><div class="ubbcode-body">I just stumbled upon this post. I'm hoping someone of you fellow hide members can help me out with figuring out my dope.

Shooting 180gr Hornaday A-Max, loaded with 77gr IMR 7828 powder and Fed 215 primers.

Haven't shot the rifle yet and my goal is to do some 1000yrd shooting with it. Any info or assistance anyone can provide is appreciated!! </div></div>
Hornady doesn't make a 180 A-max. Is it an A-max (168, 178, or 208), or one of the 180 grain SST or Interbond bullets with the red tip? It makes a difference on the BC between these bullets.
You can go here to input the data. I'll help you best I can.
http://www.mega.nu:8080/traj_dat.html

 

[srt_1]

Re: Loads for .300WM-.300WSM

ChadTRG....thanks, I'll check it out and see if I can come up with some dope info. When I bought the rifle, it came with 300 rounds. The guy put on 180gr A-Max on the boxes.

The ammo does have the red tips. Thanks for your input!

 

[rayoss232]

Re: Loads for .300WM-.300WSM

There is some Seriously accurate Rigs in here.......i really need to get my head around these reloads.......

 

[JWHITE]

Re: Loads for .300WM-.300WSM

300 WSM

200gr SMK
66gr RL-19
Fed 215
Rem Brass
Rem 700 SPS-V 26"
2890fps


consistently better than MOA out of my rifle, I need to measure the groups. Tried these out on 100-120 lb whitetail and they leave one heck of a hole, but 5 of 5 have ran about 50 yds. Plenty of blood but still unacceptable in my book. Great for paper though.

 

[MountainRogue]

Re: Loads for .300WM-.300WSM

.300 Win Mag load data needed please...

I am running a Rock 27", 1-11 twist, M-24 profile barrel, RWS (Rheinisch-Westfälischen Sprengstoff) brass, CCI BR2 primer, .208 AMAX with Retumbo powder. Need amount of Retumbo behind the 208 AMAX.

Anyone else using Retumbo?

I wrote Hornady to get the load data and they replied they haven't tested Retumbo. Hodgdon told me 85gr but I want to confirm.

Please advise since I have searched and can't find a load anywhere on here. If you use Retumbo a PM would be greatly appreciated.

Regards,

MR

 

[jerseymike]

Re: Loads for .300WM-.300WSM

Rifle:
Alan Brown built 300WM, Bartlein 1/11, finished at 26" with a Badger FTE brake,and used the same reamer developed for the MK248 220 SMK ammo

Ammo:
Win case
Rem primer
77.0 Gr of H1000
220 SMK
OAL-3.500
2840 FPS (average) using CED M2
no pressure signs
best 100 yard group ive done measured at .273 (5 shots)

I tried 77.5 grains of H1000 and got a little over 2880 (average) and showed minimum pressure signs (flat primer and very slight ejector impression) but no sign of hard case extraction.

Both loads shot extremely accurate, but with the pressure signs of the 77.5 load I will probably bump it down to 77.2 just to keep the FPS around or above 2850

 

[Tactical30]

Re: Loads for .300WM-.300WSM

Any 178gr. A-MAX load data????

 

[aoerding]

Re: Loads for .300WM-.300WSM

Did some long awaited testing today and so far so good..

-Stock Remington 700P .300WM w/ FTE brake NF 5.5-22x50 NP-R1
-Federal Brass
-215LM Primers
-Hornady 208-A MAX jammed .010 into lands OAL: 3.645" 2.911" to ogive

Loaded 1 round each from 73.0 to 75.8 in .2 increments. total of 15 rounds shot @ 100yds. I do believe i have not found the MAX charge for these loads nor do i know the fps because no chrono

but i believe the accuracy is there and for me that is good enough for the moment. The three holes close to the bulls eye were not part of these loads but starting from the bottom to the first hole of the shoot in see is my data. The charges that grouped the best were 73.2 73.4 73.6. next I'll load 5 rounds of each better charge and see which one is the best. hope this helps!

 

[GardDog]

Re: Loads for .300WM-.300WSM

<span style="font-weight: bold">300 WSM</span>

Rifle: Short Action Customs tweaked Win 70, 25" ER Shaw 1:10"
Bullet: 168 gr Hornady AMAX
Case: Win (2nd loading) standard case prep
Primer: Fed 215M
Powder: 65 grains of H-414
COL: 2.84"
Chrono 10 shot info: Av - 3112 fps, Es - 46.5, Sd - 15.96
Load grouped @ 100 yds: .53" CtC

 

[GardDog]

Re: Loads for .300WM-.300WSM

<span style="font-weight: bold">300 WSM</span>

Rifle: Short Action Customs tweaked Win 70, 25" ER Shaw 1:10"
Bullet: Berger 210 gr VLD-H
Case: Win (2nd loading) standard case prep
Primer: Fed 215M
Powder: 60 grains of H-414
COL: 2.83"
Chrono 10 shot info: Av - 2724 fps, Es - 30, Sd - 11
Load grouped @ 100 yds: .61" CtC

 

[ejd049]

Re: Loads for .300WM-.300WSM

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: longrange30</div><div class="ubbcode-body">Any 178gr. A-MAX load data???? </div></div>

+1

 

[Dan Pidlypchak]

Re: Loads for .300WM-.300WSM

Hello.I Have a Remington 700 Sendero in 300WM with a 26 inch barrel.I bought some H4831 H1000 and H4350 powder.Was wondering if anyone had a Good Loading Data for this Caliber with these powders?Also what is your OAL?I am using 190SMK and 208 Amax.If anyone can help,I would appreciate it.

 

[colt933]

Re: Loads for .300WM-.300WSM

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: 300WidowMaker</div><div class="ubbcode-body">Hello.I Have a Remington 700 Sendero in 300WM with a 26 inch barrel.I bought some H4831 H1000 and H4350 powder.Was wondering if anyone had a Good Loading Data for this Caliber with these powders?Also what is your OAL?I am using 190SMK and 208 Amax.If anyone can help,I would appreciate it. </div></div>

I'm at 69.6 and 73.3gr of 4831sc with 190SMK, Win brass, Rem mag primers, OAL ~= 3.340", 700P 26".

I'm going to start on the 208 Amax and H1000 in a few weeks.

 

[Dan Pidlypchak]

Re: Loads for .300WM-.300WSM

Thanks for the info.Will H4831 and H4831SC have the same loading charge for the 190SMK?I relize SC is for a short cut grain.Clairification on this would be appreciated.I have H4831 only and am just trying to make sure I can use the same gr density in 190.I have already loaded 208 Amax with H1000 for 300WM.My data was 74.5grn H1000 at 3.500"OAL.I am going to the range this weekend to dope in these loads.If I can shoot sub MOA at 100yds with the 208s,I will try and take them to a mile.Obviously doping at that range will take atleast 2to3 sessions,but I hear the 208 is awesome for 1500 plus.Note;I load the 208s for my TRG42 and the 190 for my 700.If you want more info on the 208,I will post upon request once I get my results.

 

[colt933]

Re: Loads for .300WM-.300WSM

Yes, I believe H4831 and H4831SC have the same burn rate.

 

[ejd049]

Re: Loads for .300WM-.300WSM

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: aoerding</div><div class="ubbcode-body">Did some long awaited testing today and so far so good..

-Stock Remington 700P .300WM w/ FTE brake NF 5.5-22x50 NP-R1
-Federal Brass
-215LM Primers
-Hornady 208-A MAX jammed .010 into lands OAL: 3.645" 2.911" to ogive

Loaded 1 round each from 73.0 to 75.8 in .2 increments. total of 15 rounds shot @ 100yds. I do believe i have not found the MAX charge for these loads nor do i know the fps because no chrono

but i believe the accuracy is there and for me that is good enough for the moment. The three holes close to the bulls eye were not part of these loads but starting from the bottom to the first hole of the shoot in see is my data. The charges that grouped the best were 73.2 73.4 73.6. next I'll load 5 rounds of each better charge and see which one is the best. hope this helps!

</div></div>

Any updates? I have the same set up!!!
Just loaded 5 rounds each of 73.2, 73.4, and 73.6. I had to go 3.60 to get it in a AI mag.

 

[Gnab2]

Re: Loads for .300WM-.300WSM

Here is a little something that we came up with over the last couple of years.

300mm WSM Load
Powder Grains Primer Bullet

VV N550 73.0 Fed 215 Mag 110gr Horn VMax n/a With 15-twist bbl chambered for short bullets, ultra-accurate, hell on ground hogs.


RL 17 68.0 Fed 215 Mag 168 Barnes TSX tipped 3280
Accuracy excellent. Single-digit ES betw. 68.0 and 69.0 grains.
IMR 7828 69.5 CCI LR Mag 168gr Barnes TSX 3000 Win Nickel brass. Jump .060", 3/4 MOA. Very effective Deer/Elk Load.

RL 15 59.0 Fed 210 168gr Berger VLD 3105 Vel in 24" bbl. Hunting load--hammers deer.

VV N560 70.0 WLR 175gr Berger VLD 3190 1/2 MOA or less in 28" Krieger 12-twist barrel. Just touching lands.

H4350 63.0 Fed 210M 175gr Sierra MK 2960 Greg Anderson hunting load. Win Brass. Very Accurate in 11-twist, carbon-wrapped 26" bbl.

H4350 63.0 Wolf LR 180gr Barnes Triple Shock 2975 Win Brass. Hunting load for Savage 16. Serious Recoil.

RL 22 70.0 Win LR Mag 180gr Barnes Triple Shock 3025 Elk load. ES of 16. Great hunting bullet. 1.2" group at 100 in factory m70.

Win 760 66.0 Fed 215 Mag 180gr Nosler Accubond 3030 Hunting load seated off lands. 3/4 MOA at 100.

H4831sc 68.0 Fed 210M 180gr Nosler Accubond n/a Win Brass. 2.86" COAL. Half-MOA, 3-shots, almost no vertical in Savage sporter.

H4831sc 64.0 CCI BR2 210 Berger VLD 2850 Long-range BR load in Norma brass. Very accurate in 10-tw Krieger. Norma seems better than Win brass.

H4350 60.0 CCI BR2 210 Berger or 210 SMK 2855 Long-range BR load in Norma brass--has won many WmPort matches. Very low ES. Vel in 30" bbl. Fed 210M works also.

VV N165 64.0 CCI BR2 210 Berger or 210 JLK 2850 Long-range BR load. Norma brass. Very accurate, 1/4 MOA at 200 yards. Also try N160, 61.0 grains.

Hope that this helps and have fun.

 

[jwoolf]

Re: Loads for .300WM-.300WSM

I'll post what I got working a couple of days ago.

300wm
26" 1:10twist LW barrel with brake.
700 action

220gr sierra match king
H1000 powder 73.6gr
Win brass
Rem 9 1/2m primers

This was loaded at .010 off the lands and OAL was about 3.526 in my chamber.

It shot .26" groups of 5 rounds in my rifle. It stayed accurate to 73.3gr and then accuracy fell off at 73.0gr and 73.9gr but, it shot .31" 5 round group at 73.3gr also.

 

[Black-X]

Re: Loads for .300WM-.300WSM

..

-X

 

[DIBBS]

Re: Loads for .300WM-.300WSM

Which Boolit with the above loads Black-X?

 

[midgetorama]

Re: Loads for .300WM-.300WSM

300 Win Mag

26" barrel, 1:10 twist

75.7 gr H-1000
Berger 210 gr VLD, naked just touching the lands at ~3.575" COAL
CCI250
WW Brass, match prepped
0.003" neck tension

Here are the chrony results from a 10 shot string:

2864, 2867, 2866, 2860, 2868, 2861, 2865, 2866, 2864, 2869

Groups are around 0.3 MOA until I get to 1000 yards, then open up to about 0.6 MOA most likely due to the shooter.

 

[aoerding]

Re: Loads for .300WM-.300WSM

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: ejd049</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: aoerding</div><div class="ubbcode-body">Did some long awaited testing today and so far so good..

-Stock Remington 700P .300WM w/ FTE brake NF 5.5-22x50 NP-R1
-Federal Brass
-215LM Primers
-Hornady 208-A MAX jammed .010 into lands OAL: 3.645" 2.911" to ogive

Loaded 1 round each from 73.0 to 75.8 in .2 increments. total of 15 rounds shot @ 100yds. I do believe i have not found the MAX charge for these loads nor do i know the fps because no chrono

but i believe the accuracy is there and for me that is good enough for the moment. The three holes close to the bulls eye were not part of these loads but starting from the bottom to the first hole of the shoot in see is my data. The charges that grouped the best were 73.2 73.4 73.6. next I'll load 5 rounds of each better charge and see which one is the best. hope this helps!

</div></div>

Any updates? I have the same set up!!!
Just loaded 5 rounds each of 73.2, 73.4, and 73.6. I had to go 3.60 to get it in a AI mag. </div></div>

update for ejd049,
100yd groups, fired 3 rounds at each target
the top left target actually has 4 rounds one being a "cold bore" shot, as for the bottom right target. hopefully next week i can chrono.

 

[Savageman110]

Re: Loads for .300WM--.300WSM

I'm loading the 208 A-max.
Powder:RL22-72.6 grns (book 72.4)
Primer: CCI 250 mag.
Case: Win
Neck sized .332
Primer Pockets Squired.
Seated Dept. .33 off the lands, AOL 3.633 3.600 to fit my magazine.
5 shot group low 2940. 2951, 2955, high, 2961, 2961, Avg, 2957 FPS.

Rifle
Savage 110
Pac nor SS barrel .890 conture
26 in 1/11 twist 5 land grove, fire lapped with 1200 grit.
.198 groups @ 100 yrds
Still working on 1000 yrd loads

 

[Ackley Improved]

Re: Loads for .300WM--.300WSM

300WSM- 28" Lilja

200 Sierra matchking
62.9 grains H4350
CCI BR2 primers
Velocity 2905fps
Cases show little sign of pressure issues.

Winchester brass, primer pockets uniformed, flash holes deburred, very light neck turn to take down high spots (Winchester 300WSM poor neck uniformity), then annealed.

Rifle very accurate

 

[crumpett]

Re: Loads for .300WM--.300WSM

300WM Remington action/Lilja barrel 24" 1-10twist
Rifle built by X-ring accuracy

Remington brass
WLR primer
67grs H4831
240SMK
COAL 3.490
Accuracy in the .1's&.2's

 

[colt933]

Re: Loads for .300WM-.300WSM

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: colt933</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: 300WidowMaker</div><div class="ubbcode-body">Hello.I Have a Remington 700 Sendero in 300WM with a 26 inch barrel.I bought some H4831 H1000 and H4350 powder.Was wondering if anyone had a Good Loading Data for this Caliber with these powders?Also what is your OAL?I am using 190SMK and 208 Amax.If anyone can help,I would appreciate it. </div></div>

I'm at 69.6 and 73.3gr of 4831sc with 190SMK, Win brass, Rem mag primers, OAL ~= 3.340", 700P 26".

I'm going to start on the 208 Amax and H1000 in a few weeks. </div></div>

I have an EXCELLENT load for my stock 700P in .300 WinMag now. Three shots in 3/4" at 200 yards. I can't wait to get it out to 1000.

208 Amax jammed .010" into the lands
Win brass with minor prep
H1000 78.9gr
CCI magnum primers

All loads between 78.0 and 79.2gr H1000 with this bullet and seating depth, case, and primer, have produced sub-MOA 3 shot groups in this rifle at 200 yards. I'll work a little more in this charge range to come up with a compromise between group size and velocity spread.

 

[david walter]

Re: Loads for .300WM-.300WSM

Anyone found a source for the 208 grain AMAX yet?

Everywhere I look they are out.

 

[jagged77]

Re: Loads for .300WM-.300WSM

Anyone used VV N570 for the 300WM / 208 A-max's? I am looking to work up a load with that specific combination and scouring any source I can for load data. I've mailed Lapua and Hornady too so hopefully I'll also have some info to share soon. In the mean time if anyone can help...

Cheers
Ed

***Update***

OK both Lapua and Hornady have no data for this combination. Hornady were kind enough however to email me all the data they had. Fortunately I have other powders on the shelf that they have tested with. Might try the 570 however using Lapua's 220 grain load.

 

[remus64]

Re: Loads for .300WM

I have a factory 300 wm rem 700 bdl. Will this gun shoot the same as yours? I just got into reloading and I am looking to find the right powder measurment with retumbo and the 210vld berger. any info on this load would be helpful. thx rob

 

[remus64]

Re: Loads for .300WM

oh also I am using 2 shot remington brass with a 250 cci primer

 

[david walter]

Re: Loads for .300WM-.300WSM

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: colt933</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: colt933</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: 300WidowMaker</div><div class="ubbcode-body">Hello.I Have a Remington 700 Sendero in 300WM with a 26 inch barrel.I bought some H4831 H1000 and H4350 powder.Was wondering if anyone had a Good Loading Data for this Caliber with these powders?Also what is your OAL?I am using 190SMK and 208 Amax.If anyone can help,I would appreciate it. </div></div>

I'm at 69.6 and 73.3gr of 4831sc with 190SMK, Win brass, Rem mag primers, OAL ~= 3.340", 700P 26".

I'm going to start on the 208 Amax and H1000 in a few weeks. </div></div>

I have an EXCELLENT load for my stock 700P in .300 WinMag now. Three shots in 3/4" at 200 yards. I can't wait to get it out to 1000.

208 Amax jammed .010" into the lands
Win brass with minor prep
H1000 78.9gr
CCI magnum primers

All loads between 78.0 and 79.2gr H1000 with this bullet and seating depth, case, and primer, have produced sub-MOA 3 shot groups in this rifle at 200 yards. I'll work a little more in this charge range to come up with a compromise between group size and velocity spread. </div></div>

What's your overall length on this load?

 

[david walter]

Re: Loads for .300WM-.300WSM

78 grains H4381sc
Sako brass
165 grain TTSX
Seated so bottom grove sits at the case mouth (3.565 OAL)
3,100 FPS
.3 at 100 yards

 

[nofinger]

Re: Loads for .300WM--.300WSM

Tagged for refernce.

 

[colt933]

Re: Loads for .300WM-.300WSM

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: colt933</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: colt933</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: 300WidowMaker</div><div class="ubbcode-body">Hello.I Have a Remington 700 Sendero in 300WM with a 26 inch barrel.I bought some H4831 H1000 and H4350 powder.Was wondering if anyone had a Good Loading Data for this Caliber with these powders?Also what is your OAL?I am using 190SMK and 208 Amax.If anyone can help,I would appreciate it. </div></div>

I'm at 69.6 and 73.3gr of 4831sc with 190SMK, Win brass, Rem mag primers, OAL ~= 3.340", 700P 26".

I'm going to start on the 208 Amax and H1000 in a few weeks. </div></div>

I have an EXCELLENT load for my stock 700P in .300 WinMag now. Three shots in 3/4" at 200 yards. I can't wait to get it out to 1000.

208 Amax jammed .010" into the lands
Win brass with minor prep
H1000 78.9gr
CCI magnum primers

All loads between 78.0 and 79.2gr H1000 with this bullet and seating depth, case, and primer, have produced sub-MOA 3 shot groups in this rifle at 200 yards. I'll work a little more in this charge range to come up with a compromise between group size and velocity spread. </div></div>

OK, I settled on the above load:

208 Amax jammed .010" into the lands
Win brass with minor prep
H1000 78.9gr
CCI magnum primers

median velocity 2874
extreme spread 21

5 shot groups average 1.5" at 200 yards
several 3 shot groups at 3/4" at 200 yards

It looks like this will still be supersonic at 1760 yards if I got the BC right - like I will ever have the chance to shoot at that distance.

All velocity numbers are with AAC 762-SD installed over an AAC brake. It's pretty amazing shooting the .300WM with a can! The .300WM sounds the same as a .308 with the can - like a .22lr from a rifle. The main sound is the crack of the bullet flight - and the impact of the bullet. Group size with and without the can are identical but point of impact is about 2" low with can on at both 100 and 200 yards and is repeatable and is the same as POI shift on the .308 bolt gun.

 

[jagged77]

Re: Loads for .300WM-.300WSM

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Jagged77</div><div class="ubbcode-body">Anyone used VV N570 for the 300WM / 208 A-max's? I am looking to work up a load with that specific combination and scouring any source I can for load data. I've mailed Lapua and Hornady too so hopefully I'll also have some info to share soon. In the mean time if anyone can help...

Cheers
Ed

***Update***

OK both Lapua and Hornady have no data for this combination. Hornady were kind enough however to email me all the data they had. Fortunately I have other powders on the shelf that they have tested with. Might try the 570 however using Lapua's 220 grain load. </div></div>

Using the data the Hornady kindly sent I worked up using IMR4831 finally settling on the max load as the best.

Specs as follows:

700P AICS stock

Remington Brass fl resized and prepped
CCI 250 mag primers
68.7 grains IMR4831
Based on drop at 300 / 500 I'm estimating around 2900 fps (although Hornady list this load around 2800 fps)
Bullet jammed .010" into lands

This bullet is incredibly slippery in the wind! Shot it yesterday in an F-Class comp and finished 2nd, no group photos to show unfortunately.

 

[hombre]

Re: Loads for .300WM-.300WSM

300 win.mag.
Sako trg
210 Berger VLD
C.O.A.L 3.53
win. brass
CCI 250m primer
RL 22 72.4gr
2900 avg. fps
1 holer at 100
1.775" at 604yds 5 shots

 

[Captain Kirk]

Re: Loads for .300WM-.300WSM

300WM

-200gr SMKs
-73.5gr RE22
-Lapua brass
-Fed 215M primers
-OAL= 3.405
-3100 FPS (Rock 26" 1/10 5R)

4 shot group @ 340 yds

 

[LongArm]

Re: Loads for .300WM-.300WSM

what is the most accurate powder/ popular powder for the 300WSM?

I am loking at IMR/Hodgdon 4350 or RL22 or RL17 any guesses???

 

[willgaut]

Re: Loads for .300WM-.300WSM

my wsm likes rl19 with 175gr smks....I dont have any 5 shots groups to post but you can look at my tac dots sheet..

 

[LongArm]

Re: Loads for .300WM-.300WSM

any more loads for 300 WSM and IMR 4350 using 168amax or 185vld's??

 

[MCC]

Re: Loads for .300WM-.300WSM

tag

 

[joe_skeeter]

Re: Loads for .300WM-.300WSM

I am testing new loads for my AI AWSM 300 Win mag. It has a 26" barrel with break and has 1:11 right hand twist. Each target is a 10 shot group with the powder weight at the top of each target.

 

[jda2631]

Re: Loads for .300WM-.300WSM

.300 WSM in a Win model 70, 24" barrel
185gr berger VLD
65gr RL17
win brass
2.945 OAL (approx .010 - .012 off lands)

haven't chrono'd yet, but shot clover leaf at 100.

also at this length, bullets fit easily into magazine. gotta love the long mag length of winchester rifles!

 

[Rookie]

Re: Loads for .300WM-.300WSM

You guys helped me a ton with working up a load for 210 VLDs so I thought I would share the results:

300WM
Berger 210gr VLDs
Winchester Large Magnum rifle primers
Federal nickel brass trimmed to 2.610 inches
68.8 H4831
COAL of 3.505
Remington Factory Barrel
.613 MOA 3-shot group

 

[Sendero_Man]

Re: Loads for .300WM-.300WSM

GAP 300WSM Non-typical hunter
Bartlein #3, Stainless, 5R, 1-10.5 Twist
25" tube

Winchester Brass
180 Accubonds
CCI 250 primers
68.2 grns. H4831 SC
OAL of 2.881

post some pics soon...

 

[scifri44]

Re: Loads for .300WM-.300WSM

Remington 700 Police 300 WM

26in factory barrel with vais brake
1-10 Twist

RP brass
190 MK
Fed 215 Large Magnum Primer
75.0grs of AA3100 at 3115 FPS
Trimed to 2.600
C.O.A.L 3.600
.5 MOA at 100

 

[stefan73]

Re: Loads for .300WM-.300WSM

Awesome thread! Thanks!

 

[Bob L Swagger]

Re: Loads for .300WM-.300WSM

tag

 

[stefan73]

Re: Loads for .300WM-.300WSM

210 Bergers through my Rem 700 Sendero using
RE22 at 73 grns
Velocity was a very consistant 2880
It shot extremely well!

Let me expand on this 26" Sendero Barrel 1-10tw with a Sako break.

 

[Rotortuner]

Re: Loads for .300WM-.300WSM

tag