**6 Creedmoor**

Just shot my new Axisworks built 6CM yesterday.

Lone Peak Fuzion TI SA DBM
TacOps carbon fiber bolt knob
24" Proof Research Sendero 1:7.5"
Axisworks 3 port brake
Manners Elite PRS2 in Tac Swamp
Axisworks SOL DBM w. AI mags
Trigger Tech Diamond @ 6oz
All metal in Cerakote Elite Sand
Seekins alloy 30mm medium rings
Tangent Theta TT315M 3-15×50 w. Gen 2XR MIL

Lapua SP brass
Fed GM205M
41.0-44.0 H4350
105 Hybrid

Had speeds.from 2950 to 3200 with no pressure. Everything except the 1st group with the cold/clean/new shot was under .5", and had two great groups in the .2-.3s.
42.0 = .240" @ 3056
44.0 = .302" @ 3200

20181028_074437.jpg
20181028_074505.jpg
20181028_084437.jpg
 
Just shot my new Axisworks built 6CM yesterday.

Lone Peak Fuzion TI SA DBM
TacOps carbon fiber bolt knob
24" Proof Research Sendero 1:7.5"
Axisworks 3 port brake
Manners Elite PRS2 in Tac Swamp
Axisworks SOL DBM w. AI mags
Trigger Tech Diamond @ 6oz
All metal in Cerakote Elite Sand
Seekins alloy 30mm medium rings
Tangent Theta TT315M 3-15×50 w. Gen 2XR MIL

Lapua SP brass
Fed GM205M
41.0-44.0 H4350
105 Hybrid

Had speeds.from 2950 to 3200 with no pressure. Everything except the 1st group with the cold/clean/new shot was under .5", and had two great groups in the .2-.3s.
42.0 = .240" @ 3056
44.0 = .302" @ 3200

View attachment 6962918View attachment 6962920View attachment 6962922
Nice! Congrats. Love the 6mm Creedmoor.
 
6mm Creedmoor
105 Berger Hybrid
Hornady 6CM brass
H4350 @ 43.4 & 44.0
2.205- base to ogive
Wolf LR primer
The 43.4 is running @ 3090ish
The 44.0 is running @ 3150ish
The brux barrel only has 70 rounds through it. I have been seeing some velocity jumps as it breaks in. This is also something RTO witnessed on his 6mm bartlein while the barrel was settling in.
One five round group across the oehler went as follows: @ 43.4
3084
3092
3081
3089
3087
mean- 3086
ES- 11
SD- 4
This load seems to be giving good numbers and vertical. As the barrel gains some speed we'll see if this load holds true for this rifle.
These were loaded with a RCBS CM.
Stiller Tac 30
Brux 6mm 1-8 @ 26"
JEC brake


Did you have any pressure signs? Im at 42.6 with a RPR 26" barrel with no pressure signs.
 
I have scoured the net trying to find some data on Varget... NOTHING! NO data for it anywhere, and I'm too new to reloading to think about trying to wing it on my own!

I have the October 2016 issue of Handloader Magazine. There is an article on reloading the 6mm Creedmoor beginning on page 34. The author of the article, John Haviland, included a chart on page 36 showing the performance in a JP Rilfes semi-auto for various powders. Regarding Varget, he gives three loads, 34.5 grains at 2,691 fps group size .70 inch, 35.5 grains at 2,780 fps group size .96 inch, 36.0 grains at 2,818 fps group size .80 inch.

He mentions that the JP web site has a statement that gas guns will not tolerate the pressures that a bolt gun will so loads are conservative.
 
Anyone else using Rl23?

I'm running 43.1 grns in my 6mm Rpr behind 103eldx touching lands. 3050ish fps.

Its working but es is up there.
 
  • Like
Reactions: WT1
Been working on my 6CM loads. Finalized my light load. Need to finish up my hunting load next. Hunting load is right at 3200fps w. 105 Hybrids.

Lapua SR 6.5CM brass necked to .273" then run through an expanding mandrel @ .241".
Fed GM205M
42.0 H4350
105 Berger Hybrid
2.206" CBTO
3027fps
ES 3
SD 1.5

Next 3 round group was similar
ES 4
SD 1.7
Avg 3027





200 yards


404 yards, 5 shots
 
My go to load is 41.5 grains of H4350 pushing a 110 gr smk at about 3015 ft/sec using Lapua srp brass and a cci 450 primer. That gives me an SD of 5 and an ES of 15 over 10 rounds.

This was my go to load. Last time I went out, this load shot 1.8 moa at 100 yds. Is anyone else seen inconsistencies between boxes of 110's? The 108 gr eld behind 41.25 gr of H4350 was shooting in the 0.5's and below.
 
Last edited:
  • Like
Reactions: JBELL74 and WT1
I picked up some 107's and 110's. The 110 is only 3 grains heavier, or 2.7 percent, yet it is 11 percent more efficient based on the ballistic coefficients. Looking at the 110 you can see there is quite a bit more material ahead of the bearing surface than on the 107.
Sierra107sand110s.jpg
 
  • Like
Reactions: Strike_out
41.9gr H4350
115gr DTAC
Alpha SRP
F205M
3020 fps out of a HH 26" 1:7.5 (prior node was ~ 41.2 gr and was 2990) SAAMI speced chamber
.2 moa (ES of 7)
5 thou off lands (BTW this was my OCW .. i didnt play with seating depth yet)
 
Funny thing is, I posted this right before I went out to sight in with a new box of 110's. The groups went from the 0.4's and 0.3's to shooting 1.8 moa at 100 yds. The 110's are being about as consistent for me as they were for you.

Probably shot 2000 of the 110SMK in my 6CM and Dasher and all have been sub half moa ... never seen an issue. You buying these in 100 bullet lots - al mine were in 500 count boxes
 
I had the same consistency problems (I think its actually just called inaccurate) out of a 500ct box.
I don't know if I would call mine inaccurate. I was getting great groups out of the 1st box I was using. And with the BC of the 110 it was really attractive, now not so much. I'm going with the 105 berger vld target with 41.25 gr of H4350. That was my second most accurate load. I also get really good accuracy with 41.25 gr of H4350 and the Hornady 108 eld. The 108 eld load was very close to factory ammo too. All loads are using lapua brass and the cci 450 primer.
 
  • Like
Reactions: ShtrRdy
I did load development today of the groundhog for my Q The Fix with 26” Proof barrel.

65gr Berger BT Target
2.185” CBTO .200” jump (only seated .100 in the neck)
Starline SR 1x fired brass
Federal 205M
42.6gr Varget
3660fps average ES 6 SD 3.0

I saw over 3800fps but this is where the node was.

Also my predator load I’ve been running which is very fur friendly even on foxes:

Barnes 95gr LRX
.045” jump
Alpha large primer virgin brass
Federal 210M’s
41.6gr H4350
Avg 3151 ES 9 SD 2.6 (10 shots)
 
  • Like
Reactions: giumau1
Anyone try the lighter bullets,just sent my barrel to be spun up by West Texas Ordnance. Going to be a 16.5” 1-8. Hoping to be able to shoot the 75gr Vmax’s or 80gt BT’s. This will be my Barrel strictly for predator hunting.

If you’re going to dedicate it to light bullets get a short throat. I did load development for 65gr BT Berger’s today and the base of the bullet was over the case mouth to touch the lands. I ended up at a .200 jump to have .100 of bearing surface in the case. Luckily the bullet jumps well, but I’d get a short freebore for light bullets.
 
  • Like
Reactions: drglock
Mine is not wanting to maintain accuracy very well.

Load when I first got barrel was 40.9 gr H4350 shooting 105 hybrid at 3100. .2-.3 MOA. with .010" jump 2.798"

Now that same load its .6-.8 MOA. I am increasing COAL to maintain .010" jump. 2.818"

Any idea why I'm losing accuracy? Think its because I have so much space in cartridge with the relatively low 40.9gr load?

Throat eroded .020" in 400 rounds.
 
Have you chronoed it lately? Wondering if the added jump and longer seating depth is changing your velocity, and getting you out of the accuracy node?
Different lot of bullets or powder?

I have a 6.5SLR that I have not changed a single thing in my reloading for 2300+ rounds and it is still shooting well. Not the .1s it used to, but still in the .3s.
 
  • Like
Reactions: lennyo3034
I had exactly the same problems with the Alpha LRP brass,
Blew primers with the dtac's at about 3100 fps
Once I switched to Lapua SRP brass and RL16 problem went away.
Plus could run a little hotter and no pressure signs, (went to 3140) with the smk's 110's and then the 107's
eventually ran them at 3080-3090, next lower node. Nodes run about .6 gr of powder apart.
The 115 dtac's weren't grouping good enough for me, I'd get a really good group and then one flyer
 
  • Like
Reactions: Strike_out
Question I have, what is the significance of SRP/LRP in the 6mm creedmore. Are people getting more consistency out of one? Longer case life? Etc. new to Reloading 6creed. Thanks in advance
 
Question I have, what is the significance of SRP/LRP in the 6mm creedmore. Are people getting more consistency out of one? Longer case life? Etc. new to Reloading 6creed. Thanks in advance

I don't know about the low SD/ES stuff, the main reason I use SRP is because my brass lasts longer. If you're pushing pressures, the primer pockets will loosen up quicker in LRP vs. SRP. Thats my reason anyway.
 
Have you chronoed it lately? Wondering if the added jump and longer seating depth is changing your velocity, and getting you out of the accuracy node?
Different lot of bullets or powder?

I have a 6.5SLR that I have not changed a single thing in my reloading for 2300+ rounds and it is still shooting well. Not the .1s it used to, but still in the .3s.

I ended up picking up a Labradar and found that my barrel picked up 160(!) fps. I backed off the powder charge significantly just to make speed limit. Right now 40.5 grains of H4350 is pushing a 105 hybrid at 3150. SDs are not as good as at higher charges, but speed limit...

I have some rounds loaded with H4831sc to test out.
 
  • Like
Reactions: Jperk0278
I ended up picking up a Labradar and found that my barrel picked up 160(!) fps. I backed off the powder charge significantly just to make speed limit. Right now 40.5 grains of H4350 is pushing a 105 hybrid at 3150. SDs are not as good as at higher charges, but speed limit...

I have some rounds loaded with H4831sc to test out.


That's a pretty fast barrel with that charge weight, I ran 41.5 of h4350 and only got 3005 but that might be due to temperature.
 
I've run 110 SMKs in 2 barrels with H4350. Loads were 42.2 and 42.3 gr giving me about 3050 fps in 26" tubes. Trying out H4831SC in a new barrel now and 44.7gr is getting me 3050 and great accuracy in a 26" tube. No pressure signs with any of the loads and all rain safe.
 
In my Hawkhill 26 inch, I was getting 3130+ - with the 110's and 42.2 of RL16
Nice shooting load, right their for 200-300 rounds, then fell off.
I've got another barrel sitting in the basement, thinking of using it
for experiments on slower powders, (4831, RL23, RL26, IMR4955 and maybe H1000)
would like to see if I can get to 3100fps and have longer barrel life.
I think everyone loves their 6 creed, till they see the barrels toast in 1000 rounds +-
Been thru 3 Alot of work to keep it shooting good.
 
In my Hawkhill 26 inch, I was getting 3130+ - with the 110's and 42.2 of RL16
Nice shooting load, right their for 200-300 rounds, then fell off.
I've got another barrel sitting in the basement, thinking of using it
for experiments on slower powders, (4831, RL23, RL26, IMR4955 and maybe H1000)
would like to see if I can get to 3100fps and have longer barrel life.
I think everyone loves their 6 creed, till they see the barrels toast in 1000 rounds +-
Been thru 3 Alot of work to keep it shooting good.

In my first barrel, also a 26" Hawkhill (7.5tw), I was getting 3150 with 110s and 43.5 (iirc) H4350. Was a laser but I backed it down to a lower node at 42.3 gr (3050fps) to minimize barrel wear. I stopped shooting that barrel in big matches at about 1400 ads but I've been running it for local matches as a science experiment and it's still shooting tight at 1800+ rds now. My 2nd barrel, also a 26" Hawkhill (8tw) is at 1200+ rds now, originally ran 42.2 H4350 and had to bump that up to 42.5 when I changed powder lots to stay at 3050 fps. Still shoots great. I have another barrel chambered up for that rig but haven't spun it on yet. I have a 3rd barrel in play on my backup gun (26" Xcaliber 7.7tw) and I get 3050 fps with the 110s and 44.7 gr of H4831sc and it shoots bugholes. I'm curious to see if barrel life is longer with the H4831sc but it's easier to source in 8lbs jugs than H4350 anyways.
 
  • Like
Reactions: briang7511
Hi guys, first 6mm cm. I'm using 42.9gr Rl22 for average of 3100 or so with 103gr eldx.

I wanna move to the 105gr-115gr bullets and was wondering if I should try h4350 or some other powder?
I have a 28" 1/7T barrel.
I'm using Peterson srp brass.
I have hornady brass to I have yet to try. Hows the hornady brass life for this round?

Pic of my rifle
Rem 700 action
Krg bravo
28" criterion prefit
Athlon midas tac
Egw 20moa base
 

Attachments

  • 20190509_145234.jpg
    20190509_145234.jpg
    495.7 KB · Views: 92
Hi guys, first 6mm cm. I'm using 42.9gr Rl22 for average of 3100 or so with 103gr eldx.

I wanna move to the 105gr-115gr bullets and was wondering if I should try h4350 or some other powder?
I have a 28" 1/7T barrel.
I'm using Peterson srp brass.
I have hornady brass to I have yet to try. Hows the hornady brass life for this round?

Pic of my rifle
Rem 700 action
Krg bravo
28" criterion prefit
Athlon midas tac
Egw 20moa base

42.2 gr H4350 out of a seekins ph1 gets me 3130fps with Peterson brass shooting Berger VLD 105 .035 offlands. Average .5-.7’s our to 1000yds allllldayeveryday.
 
Nice. What length barrel? My buddy thinks h4350 might not be as good since I have a long barrel. Thoughts?

Mine is a 24in barrel.... not sure what a 28incher would do. All in all the 6creed is easy to find a load for. I think it’s just a matter of how much performance you demand. If .5moa is fine than I think you’ll find something quickly. If you want .2’s and below than you’ll need to tune the shit out of it and even then the shooter has more imperfections than the load/barrel. Good luck and post back with your results
 
I shoot a stock RPR Gen 2 in 6 Creed

Roughly 450 rounds through it and have experimented with Sierra MatchKing 107gr and Hornady 108gr ELD-M bullets, RL16 and SuperFormance powders.

So far its favorite load is

107gr Sierra MatchKing bullet
40.0gr RL16
.025 from lands
 
  • Like
Reactions: Mooseknuckles
Hi guys, first 6mm cm. I'm using 42.9gr Rl22 for average of 3100 or so with 103gr eldx.

I wanna move to the 105gr-115gr bullets and was wondering if I should try h4350 or some other powder?
I have a 28" 1/7T barrel.
I'm using Peterson srp brass.
I have hornady brass to I have yet to try. Hows the hornady brass life for this round?

Pic of my rifle
Rem 700 action
Krg bravo
28" criterion prefit
Athlon midas tac
Egw 20moa base

Get some 115 dtacs rbt for that 7T
39.0gr. H4350 Hornady brass 8 loads now on brass CCI br
I soft seat 0.030" in closing bolt shoves bullet back into case. I use a 2415" mandrill.

2975 m.v. I was getting bad Barrel Mirage with 41 gr. of h4350 and 41.5 gr. Five shots through the barrel and Barrel Mirage was pretty bad And 1 inch groups at 100 yards. but 39 grains is The Sweet Spot one hole at 100 yards. stopped the barrel Mirage also. I can shoot 10 shots before Barrel Mirage starts to be visible. It's capable of 3" 830 yards. I only shoot three shot groups no need to shoot five with something that accurate it already proved itself when you put three shots in that small of a group why shoot two more I'm not in no competition and don't care to be never was interested in competition shooting. But I shoot 3 days a week all season. It truly blows my mind that you can drill a hole through a piece of Steel and put rifling in it, and shoot a projectile with such precision. It also blows my mind that there is time meaning when you pull the trigger there is time for this the sear to release and drive the firing pin forward the firing pin hits the primer the primer is caved in and explodes and shoves a jet of gas through the center of the powder the powder Burns it does not explode the case swells the case slammed back against the bolt the bullet slams into the rifling and starts to travel down the barrel all in a fraction of time all that is done in time that I cannot fathom I have no way of measuring it. it's just interesting to me still to this day how all that happens and you can put three rounds on top of each other at 200 yards and some can do it even further.
 
I shoot a stock RPR Gen 2 in 6 Creed

Roughly 450 rounds through it and have experimented with Sierra MatchKing 107gr and Hornady 108gr ELD-M bullets, RL16 and SuperFormance powders.

So far its favorite load is

107gr Sierra MatchKing bullet
40.0gr RL16
.025 from lands
I am also shooting a stock RPR gen 2 in 6mm creedmoor.
My favorite load is:
105 Berger hybrid
41.8gr h4350
Starline brass with WLR
Base to ogive 2.187
Velocity was 3031
 
If you shoot 115 Dtac's and happen to use a hornady seater, you might want to pick up the new A-tip seating stem. It is a much better fit than the eld stem I was using. The A-tip stem fits down another .058" and is much closer to the ogive.

I'll seat some bullets later and update on if it improves bullet to bullet variation on base to ogive measurements. The ELD stem seemed to be running about .003"
 
  • Like
Reactions: CBeck
If you shoot 115 Dtac's and happen to use a hornady seater, you might want to pick up the new A-tip seating stem. It is a much better fit than the eld stem I was using. The A-tip stem fits down another .058" and is much closer to the ogive.

I'll seat some bullets later and update on if it improves bullet to bullet variation on base to ogive measurements. The ELD stem seemed to be running about .003"

After loading a few, it does in fact seem to be seating now to with in .001"
 
I've run RL26 in three different cartridges for the last year or two. But now it can't be found. That's why I decided to try out RL23. This barrel has 200rds of 115's @ 2.757" COAL, 43gr of RL26, in Alpha brass. That gets me 3000fps. I decided to try RL23 and just substituted powder but didn't change anything else. You see the results. That's with the same zero and 300yd come up.


Nice thanks again
 
  • Like
Reactions: reubenski