-
Having trouble using the site?
Contact support
Lots of great smiths out there. Fritz at Black Canyon has made AI barrels for my AT and MC. I would highly recommend his work.
The hardest part is getting a blank. The 1.35" shank is tough to find. I have a new 308 barrel being done by Dave Tooley for my MC and he said 6 months to get the blank.
No place in particular. I buy them whenever I see them as long as they are Kreiger, PROOF SS or Bartlein Heavy contour in the right twist.
Not sure. But Frank rotates the factory one 180° because it’s more comfy to him.
Competent gunsmiths grind/buff oversize pads to fit wood stocks, so I’ll bet they could also grind down an AI one to your specs.
So do I. If i cant find anything i will resort to shaving it straight
What’s that side rail for ?
Where’s your bag rider ? Where’s your sling mount ?
What’s the side rail for ?
Where’s your bag rider? Where’s your sling mount ?
Freaking Lollipop Guild killing me with Discourage
I thought they were a more joyous people
That side rail has sling mount; i did not use a bag rider today. Had a sotek one that i was not too found off. With a schmedium heavy and short atlas i made it work.
What would make a bolt “sticky”. Seems like it started after it got left out in snow /sleet at a match.
Have cleaned and recleabed. Tried oil grease hornady one shot etc. Doesn’t look like the bolt stop is mushroomed.
Bought a second atx used. One serial number away from being consecutive. Much much much smoother. First one has a pile of rounds through it so don’t think it’s about being broken in.
Thoughts ?
Have cleaned and recleabed. Tried oil grease hornady one shot etc. Doesn’t look like the bolt stop is mushroomed.
Bought a second atx used. One serial number away from being consecutive. Much much much smoother. First one has a pile of rounds through it so don’t think it’s about being broken in.
Thoughts ?
Have you swapped the sticky bolt into the second rifle to confirm it's the bolt itself, and not the action or locking ring of the first rifle?
Is it sticky with the firing pin assembly removed?
Hit the action and bolt with brake cleaner and then relube and see
@BurtG just got off the phone. AI sez to not store your Bazooka or Hubba Bubba in your chamber
Chiclets are ok, however.
Chiclets are ok, however.
Clean your chamber properly. Description says 6,5 creedmoor only though
I have had this happen
Clean the inside of the action and the chamber with a carbon remover. Go through the magwell and use a soft cloth. I use a 410 shotgun mop for the chamber. It will remove a ton of carbon.
I then clean and dry the bolt with carbon cleaner and use a good grease on the rear of each of the 6 lugs. Put a light film of grease in the grooves of the bolt body. Finally I put a thin film of grease on the bottom area of the shroud housing that slides across the rear of the action.
Grease not oil. Will run like new.
Am I the only one who wet patches molybdenum in his barrel & firing chamber so he doesn't have to carbon scrub?
That sounds super European; no i don’t do that
I hope so. Man the moly fad ended like 15 years ago. I didn’t know you could even buy it anymore.
I'm quite the fan of it, as someone who uses it in his sports cars as well. I don't see it as a fad. And I've had positive results with it.
It's freaking retarded..... Hard stop huskydriver actual out
Oil analysis and science says otherwise. If it's stupid and it works, then it's not stupid.
I would bet the carbon build up somewhere is what causes it. Moisture causes that blue/green crap to build especially when shooting suppressed in high humidity and temp swings.
Assuming it’s doing this with no round in it? Just the travel of the bolt?
My next guess would be the mag if it’s in the rifle
I guess AI didn’t develop the AI that bombproof
Burt managed to break it
I think that deserves an award right there
Burt managed to break it
I think that deserves an award right there
I think ol' Burt has won enough "awards" on this site from the administration already...
PVA is doing one rn. Not as good as their bf sale was, but the ospreys Ive had are pretty nice barrels.
Did you shave down the reptilia diving board to fit the GII razor objective bell?
Unfortunately, that's me bombing that (and most of) the stages.
Yes I took the dremel to the underside of the diving board. It was a learning experience as my first dremel project but it worksDid you shave down the reptilia diving board to fit the GII razor objective bell?
Similar threads
