6gt

[4O6shootist]

Good speed. I'm thinking of a 26" barrel. Targeting 2850 with a 115gr.

That's where I run my match rifles 35.6-36.0 H4350 with 115s 2820-2850.

 

[Gogga]

That's where I run my match rifles 35.6-36.0 H4350 with 115s 2820-2850.

I just need to find a powder that works. Either going to be Vihtavuori or Reload Swiss over here, slim pickings recently. RS62 might work.

 

[sierracharlie338]

What’s the brain trust’s opinion on a short barrel GT? Thinking 20-22 running 109s or smaller.

Reality is I’ll never have time for comps so a 26inch comp tube makes no sense. Mainly a plinker to 1000 but also short range (under 500) whitetail and pigs.

 

[4O6shootist]

What’s the brain trust’s opinion on a short barrel GT? Thinking 20-22 running 109s or smaller.

Reality is I’ll never have time for comps so a 26inch comp tube makes no sense. Mainly a plinker to 1000 but also short range (under 500) whitetail and pigs.

The top node for 105-112gr bullets is from 2950-2900 depending on bullet weight/powder. My 24" tube will run these velocities not too far from pressure, 0.7gr, which is bout 50fps, which is what you'll lose cutting 2" off, minimum. This would make things pretty spicey. I'd run a 6cm at 20-22". No problems running the creed mid 2900s with a 20" barrel. My 22" shoots really well at 3080 with 109 eldm/ rl26.

 

[sierracharlie338]

The top node for 105-112gr bullets is from 2950-2900 depending on bullet weight/powder. My 24" tube will run these velocities not too far from pressure, 0.7gr, which is bout 50fps, which is what you'll lose cutting 2" off, minimum. This would make things pretty spicey. I'd run a 6cm at 20-22". No problems running the creed mid 2900s with a 20" barrel. My 22" shoots really well at 3080 with 109 eldm/ rl26.

So let me throw this out there.

I have a 6cm (wife’s), 260 243 and several 25s. Getting rid of the 243 barrel for the GT and the gun will be run suppressed. We box stand hunt here in TX and a 24inch barrel with suppressor can turn into a circus depending on blind size lol. I’d be fine running in the 2800s. Based on data I’d be good to 500ish for my AO.

 

[4O6shootist]

So let me throw this out there.

I have a 6cm (wife’s), 260 243 and several 25s. Getting rid of the 243 barrel for the GT and the gun will be run suppressed. We box stand hunt here in TX and a 24inch barrel with suppressor can turn into a circus depending on blind size lol. I’d be fine running in the 2800s. Based on data I’d be good to 500ish for my AO.

Yeah you would. Personally if she's already shooting 6cm(and you're not tooled to load 6gt), I'd just spin up another creed. There is ammo everywhere, quality brass from several vendors. Every one I've had, has shot very well, but so does a gt. You'll likely be happy with either choice, and soubd set on the gt. I personally just really like the 6cm when it comes to hunting. I've also got a 6saum, and smith is waiting on my barrel to cut a 6prc.

 

[sierracharlie338]

Yeah you would. Personally if she's already shooting 6cm(and you're not tooled to load 6gt), I'd just spin up another creed. There is ammo everywhere, quality brass from several vendors. Every one I've had, has shot very well, but so does a gt. You'll likely be happy with either choice, and soubd set on the gt. I personally just really like the 6cm when it comes to hunting. I've also got a 6saum, and smith is waiting on my barrel to cut a 6prc.

That’s part of the reason I’m set on the GT is I have everything for it, brass dies bullets etc except a barrel. My 25creed is a hammer with 135s but it’s big and bulky. I may go 22inches and call it good lol

 

[Buck Lawman]

What’s the brain trust’s opinion on a short barrel GT? Thinking 20-22 running 109s or smaller.

Reality is I’ll never have time for comps so a 26inch comp tube makes no sense. Mainly a plinker to 1000 but also short range (under 500) whitetail and pigs.

I'm no brain trust but, I built a 20 inch GT because I already have all the stuff for it. I have a match barrel but I rarely shoot bolt action PRS stuff anymore. Love the cartridge so I gave it a whirl. Last time out my load of 33.4 gr Varget gave these results. This was rounds 100-110 out of the new barrel. I think in the next 100 rounds or so it should settle in right around 2800fps with a berger 109lrht.

 

[sierracharlie338]

I'm no brain trust but, I built a 20 inch GT because I already have all the stuff for it. I have a match barrel but I rarely shoot bolt action PRS stuff anymore. Love the cartridge so I gave it a whirl. Last time out my load of 33.4 gr Varget gave these results. This was rounds 100-110 out of the new barrel. I think in the next 100 rounds or so it should settle in right around 2800fps with a berger 109lrht.

That's awesome info thanks! How do you like the setup?

 

[4O6shootist]

I'm no brain trust but, I built a 20 inch GT because I already have all the stuff for it. I have a match barrel but I rarely shoot bolt action PRS stuff anymore. Love the cartridge so I gave it a whirl. Last time out my load of 33.4 gr Varget gave these results. This was rounds 100-110 out of the new barrel. I think in the next 100 rounds or so it should settle in right around 2800fps with a berger 109lrht.

View attachment 8462533

That's moving right along! I just ran 107smk though the womans 26" 7.5tw Hawkhill 237 bore barrel, 33.4 and they were going 2860. Has bout 160 rounds on it. This exact load did 2950 in her prior 7tw Hawkhill. Less twist, 50k longer freebore, and lower round count must be a lot the difference. I ran same exact load of 35.8hr H4350 w/ 115 dtacs in my 30, 28" 26" barreled rifles one day, there was only 50fps between all three. These were all Alpha 170fb hawkhill 7.5tw 237 bores from same batch of steel. So not quite apples to apples, but close.

 

[Buck Lawman]

Really liking the setup. Not exactly light with the TCS and M24 contour but a lot handier with the suppressor on it for sure. Those 26 inch barrels are great for the game but get long quick with a can. The load is the same as it was for my 26 inch proof prefit match barrel and at this point I don't see a need to do any further development. It's nice when it goes easy for a change! The 26 inch was running 2890 fps with the same load.

 

[drglock]

I ran same exact load of 35.8hr H4350 w/ 115 dtacs

That’s my exact load I run with my DTACS out of a 26.75” barrel.

 

[Malum Prohibitum]

So assume you are a complete noob, and you have the following barrel:

• Bartlein M24 Contour Barrel (26" Finish Length)
  -1:7.5" Twist
  chamber cut with Alpha Munitions Legacy Reamer with a .120” freebore

A big jug of Varget, a bunch of virgin Alpha brass, and the following cache of bullets

• SIerra 107 Matchking 1000 rounds
• 106 A-Tip, 1000 rounds
• Berger 109 LRHT, 500 rounds
• Berger 6mm 105 VLD Target, 500 (these were supposed to be 109 LRHT, but . . . when they arrived I saw only the yellow Berger boxes and just assumed the snipershide member shipped what he said and what I paid for. Imagine my surprise when I unpacked them weeks later, a little too late to complain, lol)

Which bullets would you use to start?

I was leaning toward the 106 A-tip. These are the factory "seconds" that everybody is having good results with. Then maybe when those run out switching to the SMK 107, then maybe getting into the Bergers.

My thoughts are mainly the price. I spent by far the least on the 106 A-tip seconds, so I thought maybe to use those up as I am learning and going to the SMKs next as the next least expensive bullets.

But please share your thoughts. Which ones would you use to start? Assume you are a complete noob to hand loading. I have been shooting mainly commercial Hornady loading before and some handholds others put together.

 

[LR1845]

@Malum Prohibitum

I'd use the 105VLD's to get a 100 or so through the barrel to get it up to speed or close and get your brass fire formed 31ish grains .020ish off the lands.

Then either bullet 106 or 107 your choice...again at .020 off the lands start at 31.5g and work up .3g at a time...CCI450 is my preferred primer.

I am shooting 108g Bergers .020 off, hornady brass, CCI450 and 32.8g Varget 24" barrel at 2800fps

 

[loclass]

What’s the brain trust’s opinion on a short barrel GT? Thinking 20-22 running 109s or smaller.

Reality is I’ll never have time for comps so a 26inch comp tube makes no sense. Mainly a plinker to 1000 but also short range (under 500) whitetail and pigs.

As a point of reference, I have a 22" GT gas gun (GAP Bartlein) and get 2850 fps with 107 SMK and 6.5 Staball. 20-22" in a bolt gun would be plenty for deer, hogs and targets out to 1k.

 

[sierracharlie338]

As a point of reference, I have a 22" GT gas gun (GAP Bartlein) and get 2850 fps with 107 SMK and 6.5 Staball. 20-22" in a bolt gun would be plenty for deer, hogs and targets out to 1k.

Good info thanks man!

 

[Malum Prohibitum]

@Malum Prohibitum

I'd use the 105VLD's to get a 100 or so through the barrel to get it up to speed or close and get your brass fire formed 31ish grains .020ish off the lands.

Then either bullet 106 or 107 your choice...again at .020 off the lands start at 31.5g and work up .3g at a time...CCI450 is my preferred primer.

I am shooting 108g Bergers .020 off, hornady brass, CCI450 and 32.8g Varget 24" barrel at 2800fps

I forgot to mention I have 2000 CCI 450 primers.

I already put more than 100 rounds through the barrel using Hornady Match (factory loaded ammunition). I had to stop using it due to pierced primers.

Thank you for your input.

 

[Langehans]

Any ideas on where to find some brass headstamped "Gay Tiger"?

 

[wildturkey2]

Any ideas on where to find some brass headstamped "Gay Tiger"?

no i don't ?

 

[4O6shootist]

Any ideas on where to find some brass headstamped "Gay Tiger"?

Pretty sure GA Precision is the only ones who get that from Alpha. At least thats the only place I've saw it in stock. Other vendors may get it too, idk.

 

[Langehans]

Thank you sir!

 

[hairy_pineapple588]

Anyone running 109 hybrids at 2700-2750? What powder and charge?

 

[Andrew863]

On Hodgdon load data. 34.3gr of H4350 will be at 2700.

 

[4O6shootist]

On Hodgdon load data. 34.3gr of H4350 will be at 2700.

Case fill will be low, I'd try H4831sc, SW4350 or N555 at 2700-2750. But if that's where I wanted to run speed wise, I'd go straight 6br.

 

[LeadMonkey]

Anyone know the correct Dillon Precision powder funnel insert for the 6GT? I don’t see one listed in their chart and don’t know of any other common 6mm with a 35 degree shoulder (closest might be an ‘I’ insert for the 6mm Rem?).

I load on a 550 press and manually drop the charges from Autotrickler V3 into an Area419 funnel but this requires a proper insert to fit the case (or one very close) thanks for your help.

 

[LR1845]

Anyone know the correct Dillon Precision powder funnel insert for the 6GT? I don’t see one listed in their chart and don’t know of any other common 6mm with a 35 degree shoulder (closest might be an ‘I’ insert for the 6mm Rem?).

I load on a 550 press and manually drop the charges from Autotrickler V3 into an Area419 funnel but this requires a proper insert to fit the case (or one very close) thanks for your help.

The PPC funnel is what your looking for... https://www.dillonprecision.com/s000233 13085 is the number.

 

[WyomingShooter]

What’s the brain trust’s opinion on a short barrel GT? Thinking 20-22 running 109s or smaller.

Reality is I’ll never have time for comps so a 26inch comp tube makes no sense. Mainly a plinker to 1000 but also short range (under 500) whitetail and pigs.

This is from a brand new 20" Carbon Six barrel. 7.5 twist.

 

[sierracharlie338]

This is from a brand new 20" Carbon Six barrel. 7.5 twist.

Nice. Just ordered a barrel and will be cutting to 20 probably. so looks like 2900 will possibly be doable.

 

[Malum Prohibitum]

This is from a brand new 20" Carbon Six barrel. 7.5 twist.

That is going about / almost as fast as Hornady Match in 6 GT was out of my 26 inch Bartlein barrel.

 

[MC Hamill]

Anyone running 109 hybrids at 2700-2750? What powder and charge?

33.5 of H4350 in a 26” had me to 2750ish It was happier at 33.9 and basically 2800flat

 

[762 ULTRAMAGA]

Can someone get me the max case length for the GT, can't find that shit anywhere..

 

[John Glidewell]

Can someone get me the max case length for the GT, can't find that shit anywhere..

Search function works

 

[wildturkey2]

I just need to find a powder that works. Either going to be Vihtavuori or Reload Swiss over here, slim pickings recently. RS62 might work.View attachment 8462297

i can't help you sorry

 

[MxTexas]

I would like to run Berger 105 and ELDM 109 out of a suppressed 22in barrel slow at around 2750 with H4350. I’m thinking 34g of H4350 would be gtg but worry about not efficiently filling the gt case. Should I do a 6gt or step down to Dasher of BR?

 

[Gogga]

I would like to run Berger 105 and ELDM 109 out of a suppressed 22in barrel slow at around 2750 with H4350. I’m thinking 34g of H4350 would be gtg but worry about not efficiently filling the gt case. Should I do a 6gt or step down to Dasher of BR?

The point of the GT is to shoot the heavies faster, if you're not doing that then a smaller capacity case makes sense.

 

[Hickswr]

The point of the GT is to shoot the heavies faster, if you're not doing that then a smaller capacity case makes sense.

Or shoot dasher or BR speeds in a standard AICS MAG without having to experiment with spacer kits and various mags.

 

[Hickswr]

I would like to run Berger 105 and ELDM 109 out of a suppressed 22in barrel slow at around 2750 with H4350. I’m thinking 34g of H4350 would be gtg but worry about not efficiently filling the gt case. Should I do a 6gt or step down to Dasher of BR?

Your plan will work but I might take a little more H4350 with a 22” barrel to make that speed.

 

[MxTexas]

Your plan will work but I might take a little more H4350 with a 22” barrel to make that speed.

You think so? My guess of 34g might be off then, I just want to run them nice and slow. Will get new MDT mags for either BR/Dasher or GT anyway. I had a 26in 6GT before and I didn't like the length with a suppressor or how the ARC and MDT AICS mags didn't run 100% for me.

 

[MxTexas]

I think I might be up to 35g of H4350 to get 2750fps out of the 22in barrel. I'm just worry about low case fill as @4O6shootist mentioned above.

 

[hairy_pineapple588]

I think I might be up to 35g of H4350 to get 2750fps out of the 22in barrel. I'm just worry about low case fill as @4O6shootist mentioned above.

Bergers lists a case fill of 104% of H4350 with 109g hybrids at 36.3g. Obviously there is variation in cases but I think you will be fine at anything between 34-35g. 35g would be 100.4% and 34g is 97.4% according to Berger. So even if you dip to 95% then you are still good to go.

 

[Hickswr]

I think I might be up to 35g of H4350 to get 2750fps out of the 22in barrel. I'm just worry about low case fill as @4O6shootist mentioned above.

I needed 35.5 gr H4350 in my last 26” GT barrel to get a 109 Hybrid to 2860. Subtract 100 fps for the 4” shorter barrel and you are where you want to be.

Your plan will work but I’d never choose a caliber around a powder. That way of thinking seems backwards to me.

FYI- Accurate AICS mags have been 100% reliable for me. MDT, not so much.

 

[MxTexas]

Bergers lists a case fill of 104% of H4350 with 109g hybrids at 36.3g. Obviously there is variation in cases but I think you will be fine at anything between 34-35g. 35g would be 100.4% and 34g is 97.4% according to Berger. So even if you dip to 95% then you are still good to go.

Thanks for the info man, this is super helpful.

 

[MxTexas]

I needed 35.5 gr H4350 in my last 26” GT barrel to get a 109 Hybrid to 2860. Subtract 100 fps for the 4” shorter barrel and you are where you want to be.

Your plan will work but I’d never choose a caliber around a powder. That way of thinking seems backwards to me.

FYI- Accurate AICS mags have been 100% reliable for me. MDT, not so much.

Yes, it's backward I found H4350 to be super temp-insensitive for me here in SoTex and I have a crap ton of it. Are you at 100% case fill at 35.5g?

 

[hairy_pineapple588]

Yes, it's backward I found H4350 to be super temp-sensitive for me here in SoTex and I have a crap ton of it. Are you at 100% case fill at 35.5g?

I’m in north tex and found the same. Over a 25 degree difference from 100 to 75 my speeds were only 13.4fps lower.

 

[MxTexas]

I’m in north tex and found the same. Over a 25 degree difference from 100 to 75 my speeds were only 13.4fps lower.

That’s good info to know.

 

[TheOE800]

Yes, it's backward I found H4350 to be super temp-sensitive for me here in SoTex and I have a crap ton of it. Are you at 100% case fill at 35.5g?

Insensitive?

 

[MxTexas]

Insensitive?

Yes, good catch

 

[Hickswr]

Yes, it's backward I found H4350 to be super temp-insensitive for me here in SoTex and I have a crap ton of it. Are you at 100% case fill at 35.5g?

No- I’ve ran 36gr in alpha brass jumping a 109 hybrid 0.080 and it wasn’t compressed.

 

[762 ULTRAMAGA]

N150 shot the best for me, single digit ES at 32 grains.
H4350 wasn't very consistent with any load I tried.

 

[4O6shootist]

I've ran over 37.8gr of H4350 to where I finally heard a lil powder crunch with 109hyb seated 40k off in a 169fb chamber. That's what I'd call 100% load density, possibly slightly compressed. But 8 know with 36.2gr at 2920 fps I could still hear powder shake in the case.